EasyManua.ls Logo

Napoleon Ascent 42 B42NTR User Manual

Napoleon Ascent 42 B42NTR
144 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
FRENCH
PG. 73
W415-1293 / J / 03.11.19
ADD MANUAL TITLE
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone 1 (866) 820-8686 • www.napoleon.com • hearth@napoleon.com
CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:
CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES
INSTALLER:
Leave this manual with the appliance
CONSUMER:
Retain this manual for future reference
ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)
NATURAL GAS MODELS:
PROPANE GAS MODELS:
Product Name / Code
(MUST use title from Price Book)
ADD ____ ILLUSTRATED
ADD PRODUCT IMAGE
CSA /
INTERTEK
LOGO
SAFETY INFORMATION
- Do not store or use gasoline or other
ammable vapors and liquids in the vicinity of
this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not
use any phone in your building.
Immediately call your gas supplier from a
neighbour’s phone. Follow the gas
supplier’s instructions.
If you cannot reach your gas supplier, call
the fi re department.
- Installation and service must be
performed by a qualifi ed installer, service
agency, or the supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certifi ed kit is used.
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
WARNING
!
ENGLISH
$10.00
FOR INDOOR USE ONLY
IF INSTALLATION + OPERATION, ADD SERIAL
NUMBER LABEL HERE
IF SEPARATE MANUALS, ADD “PLACE
BARCODE LABEL ON THE OWNER’S MANUAL”
B42NTR / B42NTRE
B42PTR / B42PTRE
INSTALLATION AND
OPERATION MANUAL
Ascent™ 42
SAFETY BARRIER

Table of Contents

Questions and Answers:

Napoleon Ascent 42 B42NTR Specifications

General IconGeneral
Fuel TypeNatural Gas or Propane
Heating CapacityUp to 1, 500 sq. ft.
Vent TypeDirect Vent
Ignition TypeElectronic Ignition
TypeGas Fireplace
Viewing Area42"

Summary

SAFETY INFORMATION

1.0 general information

1.1 rates and efficiencies

Details gas input, supply pressure, and manifold pressure for Natural Gas and Propane.

1.2 installation overview

Outlines recommended installation steps and provides a visual guide.

1.3 rating plate information

Explains the information found on the appliance's rating plate.

1.4 mobile home installation

Covers specific installation requirements for mobile and manufactured homes.

1.5 dimensions

Provides detailed diagrams of the appliance's physical dimensions.

2.0 venting requirements

2.1 typical vent installation

Illustrates standard top and rear vent installation configurations.

2.2 special vent installations

Covers unique venting scenarios like periscope and corner terminations.

2.3 minimum air terminal location clearances

Provides clearance requirements for vent terminal locations based on codes.

2.4 venting application flow chart

Offers flowcharts to determine vent configuration suitability for top and rear exits.

2.5 definitions

Defines key terms and symbols used in venting calculations.

2.6 elbow vent length values

Lists equivalent vent lengths for various elbow angles.

2.7 top exit horizontal termination

Explains requirements for horizontal termination with top exit venting.

2.8 rear exit horizontal termination

Details requirements for horizontal termination with rear exit venting.

2.9 top and rear exit vertical termination

Covers vertical termination requirements for top and rear exit configurations.

2.10 rear exit

Instructions for configuring the appliance for rear venting.

2.11 rear exit shield (for rear vent only)

Explains the installation of a shield for rear vent configurations.

2.12 top exit

Instructions for configuring the appliance for top venting.

3.0 rough framing

3.1 minimum framing dimensions

Specifies minimum dimensions for rough framing around the appliance.

3.2 minimum enclosure clearances

Details required clearances for combustible and non-combustible materials in enclosures.

4.0 venting installation

4.1 horizontal installation

Covers installation procedures for horizontal vent runs through walls.

4.2 vertical installation

Details installation procedures for vertical vent runs through roofs.

4.3 using either flexible vent components

Covers installation with flexible vent pipes.

4.3.1 horizontal air terminal installation

Instructions for installing horizontal air terminals with flexible venting.

4.3.2 vertical air terminal installation

Instructions for installing vertical air terminals with flexible venting.

4.3.3 appliance vent connection

Explains how to connect vent pipes to the appliance.

4.3.4 horizontal air terminal installation

Instructions for installing horizontal air terminals with rigid venting.

4.3.5 vertical air terminal installation

Instructions for installing vertical air terminals with rigid venting.

4.4 vertical through existing chimney

Details installing the appliance with existing masonry chimneys.

4.4.1 restricting vertical vents

Explains how to restrict vertical vent airflow for flame adjustment.

5.1 electronic wiring diagram

5.2 battery back-up installation

5.3 optional wall switch

6.0 gas installation

7.0 operation (electronic)

8.0 operation (millivolt)

9.0 finish framing

9.1 minimum framing dimensions

Specifies minimum dimensions for finishing framing around the appliance.

10.0 finishing

10.1 safety barrier / door removal and installation

Instructions for removing and installing the safety barrier and glass door.

10.2 front hood installation

10.3 non-combustible facing material

10.4 minimum mantel clearances

10.5 recessed installation

10.6 nailing tab installation

10.7 log placement

10.8 glowing embers

10.9 charcoal embers

Guidelines for placing charcoal embers for a realistic look.

10.10 logo placement

Instructions for applying the manufacturer's logo.

11.0 optional blower installation

12.0 adjustment

12.1 pilot burner adjustment

How to adjust the pilot burner flame size and pressure.

12.2 venturi adjustment

12.3 flame characteristics

Guidance on visually checking and comparing flame appearance.

13.0 maintenance

13.1 annual maintenance

Outlines annual maintenance tasks to be performed by a technician.

13.2 door glass replacement

13.3 care of glass

Instructions for cleaning and maintaining the appliance's glass.

14.0 replacement parts

14.1 overview

14.2 electronic valve train assembly

14.3 millivolt valve train assembly

15.0 accessories

16.0 troubleshooting (electronic)

17.0 troubleshooting (millivolt)

18.0 warranty

19.0 service history

Related product manuals