EasyManua.ls Logo

Napoleon Ascent BL36NTE-1 - User Manual

Napoleon Ascent BL36NTE-1
120 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
FRENCH
PG. 61
W415-1705 / G / 03.21.19
BL36PTE-1 / BL46PTE
ADD MANUAL TITLE
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone 1 (866) 820-8686 • www.napoleon.com • hearth@napoleon.com
CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:
CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES
INSTALLER:
Leave this manual with the appliance
CONSUMER:
Retain this manual for future reference
ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)
NATURAL GAS MODELS:
PROPANE GAS MODELS:
Product Name / Code
(MUST use title from Price Book)
ADD ____ ILLUSTRATED
ADD PRODUCT IMAGE
CSA /
INTERTEK
LOGO
SAFETY INFORMATION
- Do not store or use gasoline or other
fl ammable vapors and liquids in the vicinity of
this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call
the fi re department.
- Installation and service must be
performed by a qualifi ed installer, service
agency, or the supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certifi ed kit is used.
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
WARNING
!
ENGLISH
$10.00
FOR INDOOR USE ONLY
IF INSTALLATION + OPERATION, ADD SERIAL
NUMBER LABEL HERE
IF SEPARATE MANUALS, ADD “PLACE
BARCODE LABEL ON THE OWNER’S MANUAL”
SAFETY BARRIER
Ascent™ Linear Series
(BL46 illustrated)
INSTALLATION MANUAL
BL36NTE-1 / BL46NTE
PLACE BARCODE LABEL ON THE
OWNER’S MANUAL
f i r e - p a r t s . c o m

Table of Contents

Questions and Answers

  • M
    Madison HoltAug 10, 2025
    What to do if the Napoleon Ascent BL36NTE-1 pilot sparks but will not light?
    • P
      paynemichaelAug 10, 2025
      If the pilot sparks but doesn't light, several factors could be at play. First, check that the incoming gas line ball valve is open. If you're using propane, ensure the tank isn't empty. Air in the pilot supply line can also prevent lighting, so repeat the ignition process multiple times to purge the line. For models with a thermocouple, verify the wiring polarity is correct and ensure the pilot assembly and valve are properly grounded. You may also try resetting the program by holding the reset button on the receiver until you hear two beeps.
  • J
    Jerry Watkins MDAug 15, 2025
    Why is carbon depositing on surfaces of my Napoleon Ascent BL36NTE-1?
    • B
      btaylorAug 15, 2025
      Carbon deposits on the glass, logs, or combustion chamber surfaces of your Napoleon Indoor Fireplace often indicate that the air shutter is improperly adjusted. Return the air shutter to its specified opening. Also, make sure the air shutter opening isn't blocked by lint or other obstructions.
  • W
    wardtimothyAug 19, 2025
    What to do if the flame is impinging on the glass, logs, rocks, media or combustion chamber of my Napoleon Ascent BL36NTE-1 Indoor Fireplace?
    • N
      Nicole ToddAug 19, 2025
      If the flame is hitting the glass, logs, or combustion chamber, first ensure the media is correctly positioned. Try opening the air shutter to increase primary air. Check the input rate by verifying the manifold pressure and orifice size against the rating plate specifications. Confirm that the door gaskets are intact and create a tight seal, and that the vent liners are free of holes and properly sealed. Ensure correct installation of venting and that minimum rise per foot has been adhered to for any horizontal venting. Clean the glass with a recommended gas fireplace cleaner regularly to prevent permanent marks. Also check the door seal and exhaust for damage. If the room is in negative pressure, increase the fresh air supply.
  • P
    Peter Martin MDAug 25, 2025
    How to fix a Napoleon Indoor Fireplace remote that lights but has no spark or flame?
    • C
      Courtney DiazAug 26, 2025
      If the remote lights up but there's no spark or flame, start by replacing the batteries in both the receiver and the remote. Ensure the fireplace is being operated by the same remote that turned it on. If there's an error with synchronization, reset both the receiver and the remote. Check that the remote isn't too far from the receiver. Inspect the wire connector pins for bends and straighten them if necessary. Finally, check the valve wiring for damage, and replace the valve if needed.
  • C
    Carlos TranAug 30, 2025
    What to do if the pilot will not light on my Napoleon Indoor Fireplace and makes noise with no spark?
    • J
      Joseph HaynesAug 30, 2025
      If the pilot won't light and makes noise without a spark, verify the thermocouple/sensor is clean and the wiring is undamaged. Also, verify the interrupter block isn't damaged or too tight. Ensure connections from the pilot assembly are tight and not grounding out. The sensor rod may also need cleaning.
  • T
    Timothy GonzalezSep 4, 2025
    Why is the main burner flame blue and lazy in my Napoleon Ascent BL36NTE-1?
    • L
      Lisa HallSep 4, 2025
      A blue, lazy, transparent flame from the main burner usually indicates a blockage in the vent. Remove any blockage you find. Also, incorrect installation could be the cause, so refer to the venting section to ensure correct installation.

Napoleon Ascent BL36NTE-1 Specifications

General IconGeneral
BrandNapoleon
ModelAscent BL36NTE-1
CategoryIndoor Fireplace
LanguageEnglish

Related product manuals