EasyManua.ls Logo

Napoleon Ascent BX36 User Manual

Napoleon Ascent BX36
144 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
FRENCH
PG. 73
W415-2944 / A / 04.26.22
ADD MANUAL TITLE
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone 1 (866) 820-8686 • www.napoleon.com • hearth@napoleon.com
CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:
CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES
INSTALLER:
Leave this manual with the appliance
CONSUMER:
Retain this manual for future reference
ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)
NATURAL GAS MODELS:
PROPANE GAS MODELS:
Product Name / Code
(MUST use title from Price Book)
ADD ____ ILLUSTRATED
ADD PRODUCT IMAGE
CSA /
INTERTEK
LOGO
SAFETY INFORMATION
- Do not store or use gasoline or other
ammable vapors and liquids in the vicinity of
this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not
use any phone in your building.
Immediately call your gas supplier from a
neighbour’s phone. Follow the gas
supplier’s instructions.
If you cannot reach your gas supplier, call
the fi re department.
- Installation and service must be
performed by a qualifi ed installer, service
agency, or the supplier.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certifi ed kit is used.
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
WARNING
!
ENGLISH
$10.00
FOR INDOOR USE ONLY
IF INSTALLATION + OPERATION, ADD SERIAL
NUMBER LABEL HERE
IF SEPARATE MANUALS, ADD “PLACE
BARCODE LABEL ON THE OWNER’S MANUAL”
BX36NTRE
BX36PTRE
Ascent™ BX36
INSTALLATION MANUAL
PLACE BARCODE LABEL ON THE
OWNER’S MANUAL
Safety Barrier

Table of Contents

Questions and Answers:

Napoleon Ascent BX36 Specifications

General IconGeneral
Glass Size36 inches
Vent TypeDirect Vent
Burner TypeDual Burner
IgnitionElectronic Ignition
Weight150 lbs
Fuel TypeNatural Gas
Log SetCeramic Fiber
BTU26, 000 BTU/h
Heat OutputUp to 28, 000 BTU (NG) / 26, 000 BTU (LP)

Summary

General Safety Information

Fire or Explosion Hazard

Warning about fire and explosion risks associated with gas and flammable liquids.

Gas Leak Detection Procedure

Steps to take immediately if a gas leak is detected.

Appliance Certifications

Appliance certified to Canadian and American national standards for safety.

Appliance Safety Precautions

Hot Surfaces and Burn Prevention

Warning about hot glass surfaces and preventing burns, especially for children.

Safe Operation Guidelines

Instructions for safe operation, including handling, ventilation, and clearances.

Specific Safety Warnings

Prohibited Accessories and Modifications

Warning against using unapproved accessories and modifying the appliance.

Combustible Material Clearances

Ensuring proper clearances to avoid fire hazards from combustible materials.

California Proposition 65 Warning

Notice regarding chemicals known to cause cancer and reproductive harm.

General Appliance Information

Appliance Rates and Efficiencies

Technical specifications for gas input and pressure ratings.

Installation Process Overview

Recommended Installation Steps

Sequence of recommended steps for appliance installation.

Installation Requirements and Guidelines

Installer Qualifications and Local Codes

Mandates installation by qualified personnel and adherence to local codes.

Appliance Operating Conditions

Guidelines on operating temperatures and use of approved accessories.

Appliance Specifications and Details

Rating Plate Information

Details found on the appliance's rating plate for identification and specifications.

Mobile Home Installation

Specific requirements for installing the appliance in mobile or manufactured homes.

Appliance Dimensional Specifications

Dimensional Drawings

Illustrations showing front, side, and top views with key measurements.

Optional Appliance Features

Heat Management System

Description of the optional gravity vent kit for managing heat distribution.

Venting System Requirements

General Venting Guidelines

Essential rules for vent system support, clearance, and approved components.

Approved Venting Systems

List of compatible venting system manufacturers and their components.

Typical Vent Installation Procedures

Top Vent Configuration

Diagram and requirements for installing a top vent termination.

Rear Vent Installation Procedures

Rear Vent Configuration

Diagram and requirements for installing a rear vent termination.

Special Vent Installation Methods

Periscope Termination

Instructions for using a periscope kit to locate air termination above grade.

Corner Termination

Requirements for vent installation at a corner, including rise and length.

Vent Terminal Location Clearances

Clearance Requirements Table

Table detailing minimum clearances for vent terminals in various locations.

Venting Calculation Basics

Venting Application Flow Chart

Flow chart to determine vent configuration based on rise and run.

Venting Definitions

Explanation of symbols and terms used in venting calculations.

Venting Calculations and Elbows

Elbow Vent Length Values

Table showing equivalent vent length for different elbow degrees.

Top Exit Horizontal Termination Calculations

Formulas and graph for calculating acceptable vent configurations for top exit.

Top Exit Horizontal Vent Calculations

Multiple Elbow Venting Calculations

Formulas for vent configurations with more than one 90° elbow.

Rear Exit Horizontal Vent Calculations

Two Elbow Venting Calculations

Formulas for vent configurations with two 90° elbows for rear exit.

Rear Exit Horizontal Vent Calculations (Extended)

Multiple Elbow Venting Calculations (Rear Exit)

Formulas for vent configurations with more than two 90° elbows for rear exit.

Top/Rear Vertical Vent Calculations

One or More Elbow Venting Calculations

Formulas for vent configurations with multiple elbows for top/rear vertical termination.

Top/Rear Vertical Vent Calculations (Unacceptable)

Unacceptable Vent Configurations

Criteria for identifying unacceptable vent configurations based on calculations.

Rear Exit Vent Assembly

Rear Exit Assembly Steps

Step-by-step instructions for connecting the exhaust collar for rear exit.

Rear Exit Shield Installation

Installing the Rear Exit Shield

Instructions for installing the rear exit shield for rear vent configurations.

Top Exit Vent Assembly

Top Exit Assembly Steps

Step-by-step instructions for installing the appliance as a top vent.

Rough Framing and Enclosure

Framing and Clearance Guidelines

Warnings and recommendations for framing enclosures and maintaining clearances.

Minimum Framing Dimensions for Vents

Framing Dimension Diagrams

Diagrams showing required framing dimensions for vent sections.

Enclosure Clearances: Top Vent

Top Vent Enclosure Clearances

Specific clearance requirements for top vent enclosure construction.

Enclosure Clearances: Rear Vent

Rear Exit Enclosure Clearances

Clearance requirements for rear exit enclosure installations.

Maximum Rear Vent Clearances: Interior Alcove

Interior Niche/Bumpout/Alcove Clearances

Clearance specifications for rear vent installations in interior alcoves.

Maximum Rear Vent Clearances: Exterior Alcove

Exterior Alcove/Doghouse Clearances

Clearance specifications for rear vent installations in exterior alcoves.

Rough Framing Dimensions and Support

Rough Framing Dimensions Table

Table listing minimum rough framing dimensions for appliance installation.

Venting Installation Procedures

General Installation Warnings

Critical warnings for safe and proper venting installation procedures.

Horizontal Vent Installation Details

Exterior Wall Termination

Steps for installing a horizontal vent through an exterior wall.

Vertical Vent Installation Details

Roof and Ceiling Termination

Instructions for installing a vertical vent through a roof or ceiling.

Vent Component Types and Horizontal Terminals

Horizontal Air Terminal Installation

Steps for connecting the air terminal for horizontal vent runs.

Vent Terminal and Appliance Connections

Vertical Air Terminal Installation

Instructions for installing the air terminal for vertical vent runs.

Appliance Vent Connection

Steps to connect vent pipes to the appliance's exhaust and intake collars.

Horizontal Air Terminal with Rigid Pipe

Rigid Pipe Horizontal Termination

Steps for installing rigid vent pipes at the horizontal air terminal.

Vertical Air Terminal Assembly

Connecting Vertical Vent Components

Instructions for assembling vent pipes and terminals for vertical installations.

Venting Through Existing Chimneys

Co-linear Vent System Installation

Guidelines for installing a co-linear vent system within a masonry chimney.

Vertical Vent Restriction

Installing the Vent Restrictor Kit

Instructions for installing a restrictor plate to modify flame appearance.

Electrical System Information

Hard Wiring Connection

Requirements for hard wiring the appliance and grounding.

Wiring Diagrams

Diagrams for receptacle and electronic wiring connections.

Battery Back-up System Installation

USB Power Bank Installation

Steps for installing a USB power bank as a battery back-up for power failures.

Remote Transmitter Initialization

Pairing Remote and Receiver

Procedure for synchronizing the transmitter (remote) with the receiver.

Appliance Wiring Diagrams

Main Wiring Diagram

Diagram illustrating the electrical connections for the appliance and components.

Light and Blower Assembly Wiring

Wiring Diagrams for Lights and Blower

Diagrams showing wiring for light and blower assemblies.

Gas Supply and Nailing Tab Installation

Gas Supply Connection

Guidelines for connecting the gas supply and checking for leaks.

Nailing Tab Installation

Instructions for attaching nailing tabs for frame mounting.

Appliance Operation and Safety

Safety Before Lighting

Essential safety checks and procedures before attempting to light the appliance.

Lighting and Shut-off Instructions

Step-by-step guide for lighting the appliance and turning off the gas supply.

Pilot Ignition Mode Selection

Pilot On Demand System

Explanation of the Intermittent Pilot Ignition (IPI) and Continuous Pilot Ignition (CPI) modes.

Finish Framing: Flush Installation

Flush Finish Installation

Instructions and warnings for finishing the appliance in a flush installation.

Finish Framing: Recessed Installation

Recess Installation Guidelines

Guidelines and dimensions for installing the appliance in a recessed configuration.

Appliance Finishing Procedures

Safety Barrier and Door Removal/Installation

Procedure for removing and reinstalling the safety barrier and glass door.

Front Hood Installation

Installing the Front Hood

Steps for installing the front hood component on the appliance.

Non-Combustible Facing Material Guidelines

Facing Material Projection Guidelines

Rules for projecting non-combustible facing material from the appliance face.

Mantel Clearance Requirements

Mantel Depth and Clearance Chart

Chart and graph to determine required mantel clearances based on mantel depth.

Clearances for Electronics and Valuables

Clearances for TV and Valuables

Guidelines for maintaining clearances around the appliance for TVs and other valuables.

Log Placement and Burner Overview

Log Placement Instructions

Diagrams and instructions for correctly positioning logs on the burner.

Detailed Log Placement Instructions

Detailed Log Positioning

Step-by-step guide with diagrams for placing specific logs and pins.

Decorative Embers, Logos, and Glass Media

Glowing Embers and Charcoal Embers

Instructions for placing glowing embers and charcoal embers.

Logo and Glass Media Placement

Steps for applying the logo and placing glass media for decorative effect.

Pilot and Venturi Adjustments

Pilot Burner and Venturi Adjustment

Procedures for adjusting pilot burner and venturi settings for optimal flame.

Flame Characteristics and Visual Checks

Visual Flame Check

Importance of periodically checking pilot and burner flames for abnormalities.

Appliance Maintenance and Checks

General Maintenance Checks

Recommended checks and cleaning procedures for the appliance and venting system.

Annual Maintenance Schedule

Outline of annual maintenance tasks to be performed by a qualified technician.

Glass Care and Replacement Procedures

Door Glass Replacement

Instructions and warnings for replacing the appliance's door glass.

Care of Glass Surfaces

Guidance on cleaning the glass to prevent damage and discoloration.

Component Replacement Procedures

Night Light and Blower Replacement

Procedures for replacing the night light bulb and the appliance blower.

Replacement Parts and Warranty

Ordering and Warranty Information

Information on obtaining replacement parts, warranty claims, and part delivery.

Replacement Parts List Overview

Illustrated Parts List

Diagram and list of available replacement parts with reference numbers.

Valve Train Assembly Components

Valve Train Assembly List

List of parts associated with the appliance's valve train assembly.

Troubleshooting: Operational Issues

Common Operational Issues and Solutions

Guide to diagnosing and resolving common problems like flame issues and carbon deposits.

Troubleshooting: Ignition and Remote Issues

Pilot and Burner Ignition Issues

Solutions for problems with pilot ignition, sparking, and burner not lighting.

Remote and Receiver Malfunctions

Troubleshooting steps for remote control and receiver issues.

Troubleshooting: System and Component Issues

Component Functionality Issues

Resolving issues with lights, blower, flame aggressiveness, and system power.

SIT System Lockout Reset

Procedures for resetting the SIT system ignition box when locked out.

Napoleon Product Warranty Details

Warranty Terms and Conditions

Details of the limited warranty, conditions, limitations, and coverage periods.

Related product manuals