To Next PageTo Next PageWhat to do if pilot flame is not engulfing the thermocouple in Napoleon Madison GD80PT Indoor Fireplace?
If the pilot flame isn't fully surrounding the thermocouple, gently twist the pilot head to improve the flame pattern around it.
Why vent is re-circulating in Napoleon Madison GD80PT Indoor Fireplace?
If the vent is re-circulating, check the joint seals and the installation.
Why main burner flame is a blue, lazy, transparent flame in Napoleon Madison GD80PT?
If the main burner flame is blue, lazy, and transparent, start by removing any blockage. In very cold conditions, ice might build up on the terminal, so remove it as needed. Ensure the storm collars are in the correct location. Check the pressure readings: Inlet pressure should be 7” (minimum 4.5”) water column for natural gas or 13” (minimum 11”) water column for propane. Outlet pressure should be 3.5” water column for natural gas or 10” water column for propane. Make sure the air shutter opening isn't blocked by lint or anything else.
How to fix thermopile shorting in Napoleon Madison GD80PT Indoor Fireplace?
To address a thermopile shorting issue, try cleaning the thermopile connection to the valve and then reconnect it. If the problem continues, consider replacing the thermopile or the valve.
What to do if main burner goes out; pilot stays on in Napoleon Indoor Fireplace?
If the main burner goes out but the pilot light stays on, try turning up the pilot flame. If that doesn't work, you might need to replace the pilot assembly.
Why does white / grey film forms on Napoleon Madison GD80PT?
If you see a white or grey film forming, it's likely sulphur from the fuel depositing on the glass, logs, or combustion chamber. Clean the glass with a gas fireplace glass cleaner that's recommended. Remember, don't clean the glass when it's hot. If you don't clean the deposits regularly, the glass might get permanently marked.
Why flame is impinging on the logs or combustion chamber in Napoleon Madison GD80PT?
If the flame is hitting the logs or combustion chamber, make sure the logs are in the right spot. Try opening the air shutter to let more air in. Check the input rate by looking at the manifold pressure and orifice size, matching them to what's on the rating plate. Make sure the door's seal isn't broken or missing and that it's tight. Check that both vent liners don't have holes and are sealed well at all joints. Also, make sure any horizontal venting has the right rise per foot.
General| Type | Gas Fireplace |
|---|---|
| Fuel Type | Natural Gas or Propane |
| Ignition System | Electronic Ignition |
| Vent Type | Direct Vent |
| Warranty | Limited Lifetime Warranty |
| BTU | 30, 000 |
Details the physical measurements and diagrams of the appliance.
Key safety precautions and general installation guidelines for the appliance.
Covers installation codes, certifications, and key appliance specifications.
Explains how to interpret the appliance's rating plate for proper identification.
Lists approved vent parts, suppliers, and guidelines for vent system configuration.
Illustrates standard methods for installing the appliance's venting system.
Covers specific venting configurations, including periscope terminations.
Instructions for using a periscope kit for air termination above grade.
Flowchart for determining correct vent configurations based on rise and run.
Defines key terms and symbols used in venting calculations.
Guidance and formulas for calculating vent lengths and rise for horizontal terminations.
Formulas and guidance for calculating vent lengths and rise for vertical terminations.
General warnings and instructions for the installation process.
Guidance on protecting walls and ceilings from heat and ensuring proper clearances.
Steps for installing the vent terminal through an exterior wall.
Steps for installing the vent terminal through a roof.
Instructions for using flexible vent pipes and ensuring proper installation.
Detailed steps for connecting a flexible vent to a horizontal air terminal.
Detailed steps for connecting a flexible vent to a vertical air terminal.
Instructions for connecting the vent pipe assembly to the appliance.
Specific installation requirements for mobile and manufactured homes.
Critical safety warnings and procedures for connecting the gas supply.
Instructions and warnings related to building the appliance enclosure and framing.
Specifies minimum clearances required between the appliance and combustible materials.
Details clearances required for the appliance enclosure using non-combustible materials.
Guidance and a graph for determining safe mantel clearances above the appliance.
Safety warnings and guidelines for finishing the appliance exterior.
Step-by-step instructions for safely removing and installing the appliance door.
Instructions for removing the log shipping bracket before log installation.
Detailed steps for installing the decorative interior brick panels.
Diagram and explanation of the components and display of the remote transmitter.
Step-by-step guide for initial setup and operation of the appliance via remote.
Explanation of how to use the remote control for basic functions like ON/OFF.
How to change and verify the temperature display units (Fahrenheit/Celsius).
Instructions on using the remote transmitter as a room thermostat.
Details on the Smart Thermostat function that adjusts flame based on room temperature.
How to adjust the flame level using the remote control buttons.
Instructions for controlling the fan speed using the remote control.
Procedure to lock and unlock the remote control keys for safety.
How to control the appliance's auxiliary outlet for the Night Light feature.
Information regarding battery status and manual operation modes.
How the fireplace functions and is controlled during a power outage.
Critical warnings and compliance requirements for electrical installation.
Detailed instructions and diagrams for hardwiring the appliance's electrical connections.
General safety, lighting, and shutdown procedures for operating the fireplace.
Emergency procedures to follow in case of a gas leak.
Instructions for adjusting the pilot flame size and checking gas pressures.
Guidance on adjusting the air shutter for optimal flame characteristics.
Visual checks and comparison of pilot and burner flames for proper operation.
Steps to access and adjust the air control rod for the combustion chamber.
Important warnings and general procedures for maintaining the appliance.
Instructions for accessing the appliance's control area via the inner access panel.
Procedure for replacing the lamp and lens for the Night Light feature.
Step-by-step guide for replacing the appliance's heat circulating blower.
Instructions for safely removing the remote control receiver unit.
Procedure for safely removing the gas valve assembly for servicing.
Instructions for accessing and replacing the battery for the auto-spark module.
Guidelines for cleaning the appliance's glass, emphasizing safety and proper methods.
Method for restricting vertical vents to achieve a more traditional flame appearance.
Information on ordering replacement parts, including part numbers and descriptions.
