NETGEAR ProSafe GS105 Start Here

August 2009
This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste
Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union,
this product should be treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
© 2009 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks
of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or
registered trademarks of their respective holders. Information is subject to change without notice.
Specifications
Technical Specifications
Standards compatibility IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u 100BASE-TX
Fast Ethernet, IEEE 802.3ab 1000 BASE-T, IEEE 802.3x Flow
Control, IEEE 802.1p and TOS priority, WRR queuing
Network interface RJ-45 connector for 10BASE-T, 100BASE-TX, or 1000BASE-T
Power Adapter 12V @ 1.0A DC input
Power Consumption 4W max
Weight 300g (.66 lbs)
Dimensions
(W x D x H)
94 mm x 104 mm x 28 mm
3.7 in x 4.1 in x 1.1 in
Operating temperature 0 to 50° C (32 to 122° F)
Operating humidity 10% t0 90% relative humidity, non-condensing
Electromagnetic
compliance
CE Class B, included EN55022 (CISPR 22) and EN55024,
FCC part 15 Class B, VCCI Class B, C-Tick Class B
Power adapter safety
agency approvals
CE mark, Commercial UL listed (UL 60950-1), C-Tick, CB
Performance Specifications
Frame filter rate 14800 frames/sec max for 10M port; 148,000 frames/sec max
for 100M; 1,480,000 frames/sec max for 1000M port
Frame forward rate 14,800 frames/sec max for 10M port; 148,000 frames/sec max
for 100M port; 1,480,000 frames/sec max for 1000M port
Network latency
(using 64-byte packets)
1000 Mbps to 1000 Mbps: 2.7 μs max.
Address database size up to 4K MAC addresses
MAC Address Learning Automatically updated
Queue buffer 128 KB
NETGEAR Green
features
Auto power-down mode saves energy when ports are unused
Troubleshooting Tips
Problem Action
Power light is not lit The switch has no power. Make sure that:
• The power cord is properly connected to the switch.
• The power adapter is properly connected to a functioning power
outlet. If it is in a power strip, make sure the power strip is turned
on. If the socket is controlled by a light switch, make sure the
switch is in the on position.
• You are using the NETGEAR power adapter supplied with your
switch.
Port number light is
not lit for a connected
device, or stays on
continuously
There is a hardware connection problem.
• Make sure the cable connectors are securely plugged in at the
switch and the device.
• Make sure the connected device is turned on.
• If the Ethernet cable is connected to a NIC or other Ethernet
adapter, make sure the card or adapter is installed correctly and
is working.
• Make sure the cable is less than 328 feet (100 meters).
Technical Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of your product and use
it to register your product at http://www.NETGEAR.com/register. Registration is required
before you can use our telephone support service. Registration via our website is strongly
recommended.
Go to http://kbserver.netgear.com for product updates and Web support. For Warranty and
Regional Customer Support information, see the Resource CD that came with your
product.
GS105E_IG_28Aug09.fm Page 2 Monday, August 31, 2009 11:37 AM

NETGEAR ProSafe GS105 Specifications

Power

power consumption	14.4 W
voltage	12VAC
current	1.2A

Performance

bandwidth	10 Gbps
forward rate (10 Mbps port)	14, 800 packets/sec
forward rate (100 Mbps port)	148, 000 packets/sec
forward rate (1000 Mbps port)	1, 480, 000 packets/sec

Network Latency

latency (100 to 100 Mbps)	20 µs
latency (1000 to 1000 Mbps)	10 µs

Operating Environment

operating temperature	0 to 40º C
operating humidity	10 to 90% noncondensing
storage temperature	-20 to 70° C

Weight and Dimensions

dimensions	158 x 105 x 25 mm
weight	0.49 kg