Nibe F1330 User Manual

52 NIBE F1330
Control
Control
5.0 Heat pump
[N]
5.1 Heat pump unit [N]
5.2.0
Compressor module A [N] 5.2.1 Heating flow/return [N]
5.2.2 Brine in/out [N]
5.2.3 Hot gas temperature [U]
5.2.4 Overheating temp. [U]
5.2.5 Liquide line temp. [U]
5.2.6 Tot. starts compr. A [U]
5.2.7 Opera.time compr. A [U]
5.2.8 Return to 5.2.0
[N]
5.3.0
Compressor module B [N] 5.3.1 Heating flow/return [N]
5.3.2 Brine in/out [N]
5.3.3 Hot gas temperature [U]
5.3.4 Overheating temp. [U]
5.3.5 Liquide line temp. [U]
5.3.6 Tot. starts compr. B [U]
5.3.7 Opera.time compr. B [U]
5.3.8 Return to 5.3.0
[N]
5.4.0 Settings
[U] 5.4.1 Max.heat returntemp. [U]
5.4.2 Min brine out [U]
5.4.3 Max brine in [U]
5.4.4 Level monitor [U]
5.4.5 Start to start time [U]
5.4.6 Oper. mode brinepump [U]
5.4.7 Oper.mode heatpump A [U]
5.4.8 Oper.mode heatpump B [U]
5.4.9 Quickstart of compr. [U]
5.4.10 Factory pre-set [U]
5.4.11 Reset alarm [U]
5.4.12 Pool heat comp A [U]
5.4.13 Pool heat comp B [U]
5.4.14 Return to 5.4.0
[N]
5.5.0 Sensor calibration
[S] 5.5.1 Heating return A [S]
5.5.2 Heating return B [S]
5.5.3 Brine in [S]
5.5.4 Brine out A [S]
5.5.5 Brine out B [S]
5.5.6 Outdoor temp.sensor [S]
5.5.7 Room temp. sensor [S]
5.5.8 Flow temp. sensor 1 [S]
5.5.9 Flow temp. sensor 2 [S]
5.5.10 Return to 5.5.0
[S]
5.6 Return to 5.0
[N]
6.0 External units*
[N]
6.1.0 Circulation pumps
[U] 6.1.1 Op-mode external cp [U]
6.1.2 Periodtime economy [U]
6.1.3 Operati-time economy [U]
6.1.4 Time of period Hw-cp [U]
6.1.5 Periodtime Hw-cp [U]
6.1.6 Operatingtime Hw-cp [U]
6.1.7 Return to 6.1.0
[U]
6.2.0
Immersionheater
settings
[N] 6.2.1 Immersionheater type [U]
6.2.2 Immersionheatrelays [U]
6.2.3 Steps at 2h delay [U]
6.2.4 Quickstart el.heater [U]
6.2.5 Time factor el.cass. [U]
6.2.6 Return to 6.2.0
[U]
6.3.0 Boiler settings
[N] 6.3.1 Oil boiler time [U]
6.3.2 Start temp. shunt [U]
6.3.3 Period time shunt [U]
6.3.4 Shuntintensification [U]
6.3.5 Timefactor oilboiler [U]
6.3.6 Return to 6.3.0
[U]
6.4.0 HPAC/PKM settings
[U] 6.4.1 Cooling [U]
6.4.2 Cooling curve [U]
6.4.3 Offset cold curve [U]
6.4.4 Starttemp. heating [U]
6.4.5 Starttemp. cooling [U]
6.4.6 Start active cooling [U]
6.4.7 GM for compr.-step [U]
6.4.8 Diff Passive/Active [U]
6.4.9 Min. flow temp. [U]
6.4.10 Periodtime shunt [U]
6.4.11 Shunt intensificat [U]
6.4.12 Time betw. heat cold [U]
6.4.13 Brinepump cont. AC [U]
6.4.14 Return to 6.4.0
[U]
6.5.0 Pool settings
[N] 6.5.1 Start temp. pool [U]
6.5.2 Stop temp. pool [U]
6.5.3 Periodtime heat/pool [U]
6.5.4 Max-time heatproduct [U]
6.5.5 Max compr. to pool [U]
6.5.6 Return to 6.5.0
[U]
6.6.0 HW storage vessel
[N] 6.6.1 Loading temperature [U]
6.6.2 Per.-time ctrl.valve [U]
6.6.3 Ctrl.valve intensific. [U]
6.6.4 Zero [U]
6.6.5 Return to 6.6.0
[U]
[N] Normal menus: Displayed in all menu modes.
[U] Extended menus: Only displayed when extended or
service is selected in menu 8.1.1.
[S] Service menus: Only dispalyed when service is selected
in menu 8.1.1

Nibe F1330 Specifications

General

Brand	Nibe
Model	F1330
Category	Heat Pump
Language	English