Need help?Do you have a question about the Nibe F1330 and is the answer not in the manual?
Installation and maintenance instructions for the NIBE F1330 heat pump.
Overview and explanation of the NIBE F1330 heat pump's front panel controls and display.
Guidance on adjusting heating settings for cold and warm weather conditions.
Recommendations for installing the NIBE F1330 heat pump in suitable locations.
How to interconnect multiple F1330 units as Master and Slave.
Requirements for installation inspection before commissioning the heating system.
How to connect the heating medium pipes to the heat pump.
Guidelines for connecting the brine pipes, including considerations for freezing and insulation.
The importance and dimensioning of the pressure expansion vessel for the brine circuit.
Step-by-step procedure for filling and venting the collector system with brine.
Procedure for filling and venting the heating medium system.
A detailed diagram and explanation of a specific docking configuration.
Instructions for the main electrical installation and power supply connections.
Information about the miniature circuit breaker and its resetting procedure.
Explanation of motor protection breakers for compressors and their resetting.
Detailed instructions for connecting the heat pump to the electrical supply and terminal blocks.
Pre-start inspection procedures for heat pumps in a system.
Step-by-step guide for starting a single F1330 heat pump.
Procedure for starting up multiple F1330 units connected in a system.
Detailed instructions for configuring Master/Slave communication between F1330 units.
Selecting the operating mode (Off, Heat, Hot water, Combi, Parallel, External control) for each F1330.
Setting the operating mode for the brine pump (intermittent, continuous, economy).
Setting the operating mode for heating medium pumps.
Connecting flow and return temperature sensors for heat production.
Overview of menu settings related to heat production, including operating mode and heating curves.
How the heat pump manages hot water production and its priority over heating.
Connecting the shuttle valve and hot water sensor for hot water production.
Function to temporarily raise hot water temperature using compressor or immersion heater.
Connecting the control signal and power supply for the "Extra hot water" function.
Wiring connections for the electrical additional heater stages.
Overview of menu settings for configuring the electrical additional heater.
How the oil boiler is controlled via relay and shunt valve, including sensor connections.
Wiring details for connecting the oil boiler and its sensor.
Using the integrated function for drying new concrete floors.
Overview of menu settings for HPAC system configuration and cooling modes.
Connecting relays ETS-4 to ETS-6 for electrical additional heating.
Connecting HPAC on Expansion Card 11.
Controlling the hot water circulation pump (VVC) by time or period.
Wiring connections for the hot water circulation pump function.
Menu settings for controlling the hot water circulation pump's operation time and period.
Menu settings for pool heating, including start/stop temperatures and periods.
Connecting shuttle valve and circulation pump for pool heating.
Wiring connections for pool heating components.
Connecting a shunt valve and circulation pump for a second heating circuit.
Wiring connections for the sub shunt valve and circulation pump.
Menu settings for configuring the sub shunt valve's operation.
Controlling a groundwater pump via the F1330.
Wiring connections for the ground water pump function.
Connecting a cooling system with a 4-pipe setup.
Wiring connections for the 4-pipe passive cooling system.
Menu settings for configuring passive cooling in a 4-pipe system.
Connecting a cooling system with a 2-pipe setup.
Wiring connections for the 2-pipe passive cooling system.
Menu settings for configuring passive cooling in a 2-pipe system.
Details on PCAC cooling systems with 4 pipes, including passive and active modes.
Electrical connections and menu settings for PCAC cooling systems.
Menu settings for cooling/heating modes when using accumulators.
Electrical connections for external control of additional heat and compressor.
Step-by-step guide on how to change parameter values in the menus.
A practical example of how to change the menu type.
Shows current and calculated flow temperatures for the second heating system.
Accesses settings and read-outs for each connected heat pump unit.
Accesses settings and read-outs for external units requiring accessories.
Shows the current hot water temperature and related settings.
Displays current and calculated flow temperatures for the heating system.
Accesses the log of operating disturbances and heat pump status.
A list of all components with their part numbers and descriptions.
Diagrams showing unit dimensions and required installation space.
Troubleshooting guide for common malfunctions and operating disturbances.
General information on alarms, their display, and logging.
Alarms that automatically reset after a condition is met.
Troubleshooting for constant alarms related to sensor faults.
To Next Page
General
