Nibe F1330 - Menu Tree

51NIBE F1330
Control
Control
0.0 System [N]
0.1.0 Status
[N] 0.1.1 Status Master:A [N]
0.1.2 Status Master:B [N]
0.1.3 Status Slave 1:A* [N]
0.1.4 Status Slave 1:B* [N]
0.1.5 Status Slave 2:A* [N]
0.1.6 Status Slave 2:B* [N]
0.1.7 Status Slave 3:A* [N]
0.1.8 Status Slave 3:B* [N]
0.1.9 Status Slave 4:A* [N]
0.1.10 Status Slave 4:B* [N]
0.1.11 Status Slave 5:A* [N]
0.1.12 Status Slave 5:B* [N]
0.1.13
Status Slave 6:A* [N]
0.1.14 Status Slave 6:B* [N]
0.1.15
Status Slave 7:A* [N]
0.1.16
Status Slave 7:B* [N]
0.1.17 Status Slave 8:A* [N]
0.1.18 Status Slave 8:B* [N]
0.1.19 Return to 0.1.0
[N]
0.2.0 Oper.type setting
[S] 0.2.1 Oper. type Master [S]
0.2.2 Oper. type Slave 1 [S]
0.2.3 Oper. type Slave 2 [S]
0.2.4 Oper. type Slave 3 [S]
0.2.5 Oper. type Slave 4 [S]
0.2.6 Oper. type Slave 5 [S]
0.2.7 Oper. type Slave 6 [S]
0.2.8 Oper. type Slave 7 [S]
0.2.9 Oper. type Slave 8 [S]
0.2.10 Return to 0.2.0
[S]
0.3 Return to 0.0
[N]
* Slaves 1-8 are only shown when made operational in menu 0.2.x
1.0 Hotwater temp. [N]
1.1 Start temperature HW [U]
1.2 Stop temperature HW [U]
1.3 Stop temp. compr XHW [U]
1.4 Stop temperature XHW [U]
1.5 Interval per. XHW [U]
1.6 Periodtime HW/Heat. [U]
1.7 Maxtime HW-product. [U]
1.8 Diff between compr. [U]
1.9.0
HW with additional
heat [U] 1.9.1
Start temp. additional
heat [U]
1.9.2
Stop temp. additional
heat [U]
1.9.3 Return to 1.9.0
[N]
1.10 Return to 1.0
[N]
2.0 Flow temperature [N]
2.1 Curve slope [N]
2.2 Offset heating curve [N]
2.3 Min. flow temp. [U]
2.4 Max. flow temp. [U]
2.5 External adjustment [U]
2.6.0
Own curve
definition
[U] 2.6.1 Flow temp.at -20°C [U]
2.6.2 Flow temp.at +20°C [U]
2.6.3 Set buckling Temp. [U]
2.6.4 Flowtemp.at buckling [U]
2.6.5 Return to 2.6.0
[U]
2.7.0 Fixed condensing
[U] 2.7.1 Start temp.compressor [U]
2.7.2 Stoptemp. compressor [U]
2.7.3 Starttemp. additive [U]
2.7.4 Stoptemp. additive [U]
2.7.5 Return to 2.7.0
[U]
2.8 Return temperature [N]
2.9 Degree minutes [N]
2.10 Return to 2.0
[N]
3.0 Flow temperature 2* [N]
3.1 Curve slope 2 [N]
3.2 Offset heatingcurve 2 [N]
3.3 Min. flow temp. 2 [U]
3.4 Max. flow temp. 2 [U]
3.5 External adjustment2 [U]
3.6.0 Own curve definit.2
[U] 3.6.1 Flow temp.at -20°C [U]
3.6.2 Flow temp.at +20°C [U]
3.6.3 Set buckling Temp. [U]
3.6.4 Flowtemp.at buckling [U]
3.6.5 Return to 3.6.0
[U]
3.7 Return temperature 2 [N]
3.8 Shunt period time 2 [U]
3.9 Shunt intensificat. 2 [U]
3.10 Return to 3.0
[N]
* Accessories
4.0 Outdoor temp. [N]
4.1 Medium outdoor temp. [N]
4.2 Return to 4.0
[N]
Menu tree