ENGLISH – 3
GENERAL SAFETY WARNINGS AND
PRECAUTIONS
1
1 GENERAL SAFETY WARNINGS AND PRECAUTIONS
1.1 GENERAL WARNINGS
a
WARNING! Important safety instructions. Observe all the
instructions as improper installation may cause serious
damages.
a
WARNING! Important safety instructions. It is important
to comply with these instructions to ensure personal
safety. Store these instructions carefully.
a
According to the latest European legislation, an automat-
ed device must be constructed in conformity to the har-
monised rules specied in the current Machinery Direc-
tive, which allow for declaring the presumed conformity
of the automation. Consequently, all the operations for
connecting the product to the mains electricity, its com-
missioning and maintenance must be carried out exclu-
sively by a qualied and expert technician.
a
In order to avoid any danger from inadvertent resetting
of the thermal cut-off device, this appliance must not be
powered through an external switching device, such as a
timer, or connected to a supply that is regularly powered
or switched off by the circuit.
a
Permanently afx a label or sign to the door with the fol-
lowing image (minimum height 60 mm) "Figure 1"
1
WARNING! Please abide by the following warnings:
– Before commencing the installation, check the “Product techni-
cal specications”, in particular whether this product is suitable
for automating your guided part. Should it not be suitable, do
NOT proceed with the installation.
– The product cannot be used before it has been commissioned
as specied in the “Testing and commissioning” chapter.
– Before proceeding with the product’s installation, check that all
the materials are in good working order and suited to the intend
-
ed applications.
– The product is not intended for use by persons (including chil
-
dren) with reduced physical, sensory or mental capacities, nor
by anyone lacking sufcient experience or familiarity with the
product.
– Children must not play with the appliance.
– Do not allow children to play with the product’s control devices.
Keep the remote controls out of reach of children.
– The system’s power supply network must include a disconnec-
tion device (not supplied) with a contact opening gap permit-
ting complete disconnection under the conditions envisaged by
Overvoltage Category III.
– Handle the product with care during installation, taking care to
avoid crushing, denting or dropping it, or allowing contact with
liquids of any kind. Keep the product away from sources of heat
and naked ames. Failure to observe the above can damage the
product, and increase the risk of danger or malfunction. Should
this happen, stop installation immediately and contact Custom
-
er Service.
– The manufacturer declines all liability for damages to property,
objects or people resulting from failure to observe the assem
-
bly instructions. In such cases, the warranty for material defects
shall not apply.
– The weighted sound pressure level of the emission A is lower
than 70 dB(A).
– Cleaning and maintenance reserved for the user must not be
carried out by unsupervised children.
– Before intervening on the system (maintenance, cleaning), al
-
ways disconnect the product from the mains power supply and
from any batteries.
– Inspect the system frequently, in particular the cables, springs
and supports to detect any imbalances and signs of wear or
damage. Do not use the product if it needs to be repaired or
adjusted, because defective installation or incorrect balancing of
the automation can lead to injuries.
– The packing materials of the product must be disposed of in
compliance with local regulations.
– The product must not be installed outdoors.
– Keep an eye on moving doors and do not let anyone go near
them until they have opened or closed fully.
– Be careful when activating the manual unlocking device (manual
manoeuvre), as an open door may fall suddenly due to weak or
broken springs, or if it is unbalanced.
– Every month, check that the drive motor reverses when the door
encounters a 50 mm-high object placed on the ground. If nec
-
essary, readjust the door and check it again, as incorrect adjust-
ment is potentially dangerous (for drive motors incorporating a
trapping safety system that intervenes when the door's lower
edge encounters an obstacle).
– If the power cable is damaged, it must be replaced by the
manufacturer or by its technical assistance service or similarly
qualied person in order to prevent any form of risk.
a
Warning! If there is an automatic door, it could operate
unexpectedly; therefore, do not allow anything to hinder
the door’s path.
a
Disconnect the power supply during cleaning or mainte-
nance operations.
a
The automation must not be used with a door that incor-
porates a pedestrian door (unless the automation can be
controlled with the pedestrian door inserted).
a
After the installation, make sure that the anti-entangle-
ment protection system works as intended.
To Next Page
Loading...
Need help?
General
