EasyManuals Logo

Niles ZR-6 User Manual

Niles ZR-6
104 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #64 background imageLoading...
Page #64 background image
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-437362
PROGRAMMING THE REMOTE
ERASING A SINGLE LEARNED BUTTON
A button can return to its original programming for a selected
device. A button can also be taught a new function using the
“Programming A Learned Key” procedure in the prior section.
Please note that if more than ten seconds pass between button
presses, the remote exits the programming mode.
To Erase a Single Learned Button:
1. Press the Source button for the device whose code is to be
erased.
2. Press-and-hold the Setup button until the selected Source
button’s LED blinks twice, then release.
3. Enter 9 7 6. The Source button LED blinks twice.
4. Press the button twice that contains the learned function
to be erased. The Source button LED blinks twice and the
R-8L remote exits the programming mode.
ERASING ALL LEARNED BUTTONS FOR
A SPECIFIC DEVICE
Please note that if more than ten seconds passes between button
presses, the remote exits the programming mode.
To Erase All Learned Buttons For A Specifi c Device:
1. Press-and-hold the Setup button until the selected Source
button’s LED blinks twice, then release.
2. Press 9 7 6. The Source button LED blinks twice.
3. Press a Source button twice to clear all the learned buttons
for that device. The Source button LED blinks twice and the
R-8L exits from the programming mode.
RESTORING ALL BUTTON FUNCTIONS
TO FACTORY SETTINGS
Please note that if more than ten seconds passes between button
presses, the remote exits the programming mode.
To Restore All Button Functions To Factory Settings:
1. Press-and-hold the Setup button until the selected Source
button’s LED blinks twice, then release.
2. Press 9 8 0. The Source button LED blinks four times.
3. Press-and-hold the Setup button until the red LED blinks
twice, then release.
PROGRAMMING A SEQUENCE
TECH TIP
Any button on the Niles R-8L Hand-Held Learning
Remote Control (except the Setup button) can be
programmed with a sequence. A sequence is a set
of sequential commands initiated by one press of a
button. A typical home theater sequence might turn the TV on, turn the
home theater receiver on, select the proper input on the receiver, select
the proper input on the TV, turn the DVD player on, and put the DVD
player in to the play mode.
Please note that programming a new sequence over an existing one
erases the original sequence.
To Program a Sequence:
1. Press a Source button.
2. Press-and-hold the Setup button until the selected
Source button’s LED blinks twice, then release
3. Press 9 7 8. The Source button LED blinks four twice.
4. Press the button that the sequence is to be assigned to
5. Enter the series of commands, in the desired order, that
the sequence is to execute (up to 15 commands).
6. Press-and-hold the Setup button until the red LED
blinks twice, then release.
TECH TIP
When the button that has been programmed with
the sequence is pressed, the remote sends the
series of commands, but only if the source device
selected in Step 1 is selected. For example, A
sequence key can be programmed to turn on both the TV and the cable
box, but only if TV is selected as the source. If DVD is selected, the
button does not execute the sequence for the TV.
7. To clear the sequence, repeat steps 1-6 above, but do
not enter a series of commands at step 5.
PROGRAMMING THE R-8L HAND-HELD LEARNING REMOTE CONTROL

Table of Contents

Other manuals for Niles ZR-6

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Niles ZR-6 and is the answer not in the manual?

Niles ZR-6 Specifications

General IconGeneral
BrandNiles
ModelZR-6
CategoryReceiver
LanguageEnglish

Related product manuals