18
Key No. Qty. Description Key No. Qty. Description
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see the
back cover of this manual. *These parts are not illustrated.
PART LIST
Model No. NTIVEL57016.0
1 1 Computer
2 4 Self- tapping screw M4*16
3 1 Computer rack
4 3 Screw M5-0.8*15
5 8 Self- tapping screw M4*20
6 1 Central shaft cover
7 1 Hand pulse cable 650mm
8 4 Screw M2.5-0.45*33
9 4 End Cap Φ32*36
10 2 Hand pulse gripsΦ32
11 1 Handlebar welding
12 3 Washer Φ8*Φ16*1.5T
13L 1 Center Shaft Plastic Cover L
13R 1 Center Shaft Plastic Cover R
14L 1 Handrail welding L
14R 1 Handrail welding R
15 2 Foam Φ32*3T*510mm
16 13 Allen Bolt M8-1.25*20
17 19 Spring Washer Φ8
18 2 Washer Φ8*Φ32*3T
19 4 Powder Metallurgy 38*17*15T
20 4 Allen Bolt M8-1.25*43
21 6 Nut M8
22 2 Lower Swing Bar welding
23 2 Allen Bolt M8-1.25*86
24 4 Wave Washer Φ10*Φ15*0.5T
25 4 Iron-based Powders
Φ32*Φ10*14.5T
26L 1 Footplate Support Bar L
26R 1 Footplate Support Bar R
27 14 Washer Φ8*Φ19*2T
28 2 Washer Φ10*Φ19*2T
29 2 Plastic Cover
30L 1 Footplate L
30R 1 Footplate R
31 2 Eva Foamed Tapes 20*250*3mm
32 2 Eva Foamed Tapes 20X40X3
33 6 Allen Bolt M8-1.25*45 5mm
34 2 Washer Φ8*Φ24*2T ucp
35 2 Tube Spacer Φ17.5*Φ22*12mm
36 2 C-Sharp Clip Φ40
37 2 Bearing 2203-2RS
38 2 Crank Connect Cover
39 2 Screw M5*7.5
40 6 Drill Screw M5*20
41 1 Plastic Cover
42L 1 Chain Cover L
42R 1 Chain Cover R
43 3 Plastic screw
44 11 Drill Screw M5*15
45 2 Crank plug
46 2 Round Cover
47 2 Flange Screw M10-1.25*10T
48 2 Cross
49 8 Self- tapping screw M4.5*15
50 2 Axle Cap
51 1 Nut M10*1.25*6T
52 2 Chain Adjuster Set
53 1 C-Sharp Clip Φ20
54 1 Washer Φ20*Φ25*2.0T
55 1 Sensor with Cable1000mm
56 1 Main Frame
57 1 DC Cable 1000mm
58 2 Eva Foamed Tapes 60*90*2
59 2 Rear End Cap
60 1 Rear stabilizer
61 4 Allen Bolt M8-1.25*92mm
62 2 Bearing 6004-2RS
63 3 Washer Φ20*Φ25*1.0T
64 1 Wave Washer Φ20*Φ25*0.5T
65 1 Belt Wheel Φ440*20.2
66 1 Round Metal Plate welding
67 4 Screw M8-1.25*12
68 1 Belt 690J6
69 5 Self- tapping screw M4.5*25
70 10 Magnet 40*25*10
71 3 Washer Φ6*Φ14*1.5T
72 2 Allen Bolt M6*15
73 2 spring Φ6
74 1 Rotating spindle Φ12*33.2
75 1 Magnet Steel Frame
76 1 Nut M10-1.25*10T
77 1 Idler wheel mandrel Φ10*42mml
78 1 Idler wheel Φ37*20.5L
79 1 Washer 8*16*2T
80 2 C-Sharp Clip Φ10
81 1 Nut M6
82 1 Spring Φ1*12
83 1 Screw M6*80
84 2 Nut M6
85 1 Fly Wheel Φ300*34
86 2 Bearing 6000-2RS
87 1 Mandrel M10*1.25
88 2 Nut M10*1.25
89 1 Flange Screw M10*1.25*10T
90 1 Wire 1000mm
91 1 Motor
92L 1 Front End Cap L
92R 1 Front End Cap R
93 1 Front stabilizer
94 1 Lower computer cable 800mm
95 1 Front Plastic Cover
96 1 Upper computer cable 1250mm
97 4 Screw M4-0.7*15
98 1 Tablet Holder
99 1 Handlebar Post
100 2 Wave Washer Φ17*Φ25*0.5T
101 1 Allen key wrench 5mm
102 1 Adaptor
103 1 Combination Wrench
To Next Page
Loading...
