AFP-200 Instruction PN 15511:F2 10/11/99 51
Programming Hint
The control panel includes a special recall function to display the last 19-character label used, which can save
many keystrokes. When the blinking cursor is over the first letter of the label field, press the zero key twice to
display the label entered for the previous point. If the last character of the label is a number, pressing the zero
key a third time will increment this number. Once the label is recalled, you can edit the each character of the
label.
To load the point’s program into memory at any time,
press Enter. After pressing Enter, the autoprogram
routine displays the next new detector.
If a detector exists in the control panel program, but is
missing (no answer), the display shows the screen to
the right.
If you press Enter, the control panel deletes the device
from memory and autoprogram displays the next new
device. If you press the left cursor, the program remains unchanged, and the next new device displays.
When autoprogram finishes displaying all new detectors, autoprogram displays the first new module with the
lowest address.
Monitor Module Autoprogram
Monitor module autoprogram is similar to detector
autoprogram. A sample LCD display of a typical
Monitor Module autoprogram screen appears to the
right.
The major program editing for Monitor Modules is the
selection of the type code on the first line. To change
this selection, use the up and down cursor keys as the
entire field blinks. The default selection is “Monitor,”
as shown in the screen to the right. Note: Selection of a type code may change the functional operation of that
point. Figure 3-1 contains a list of Monitor Module type codes.
PROGRM@SMOKE(PHOTO)
FLOOR1@MAIN@LOBBY
DEVICE@NOT@ANSWERING
DELETE@FROM@MEM?@D01
PROGRM@MONITOR
MODULE@ADDRESS@01
ZO4@Z@@@@Z@@@@Z
@@@@@@@@@@@@@@@@M01
LEBALEDOCEPYTLEBALEDOCEPYT
LEBALEDOCEPYT
LEBALEDOCEPYTLEBALEDOCEPYTNOITCNUFLAICEPSNOITCNUFLAICEPS
NOITCNUFLAICEPS
NOITCNUFLAICEPSNOITCNUFLAICEPS
ROTINOM)tluafed(enoN
NOITATSLLUPenoN
TCETEDEKOMSenoN
TCETEDTAEHenoN
knalBseilppaedocepytrehtoonnehwtceles,enoN
WOLFRETAWmralAelbaecneliS-noNasesuaC
YROSIVREPUS
noitarepOeeS(tnioPyrosivrepuSasemoceB
)retpahC
REPMAT
noitarepOeeS(tnioPyrosivrepuSasemoceB
)retpahC
ERIFNON
noitarepOees(tnioPmralA-nonlaicepS
)retpahC
TRELADRAZAH
noitarepOees(tnioPmralA-nonlaicepS
)retpahC
LORTNOCERIF
noitarepOees(tnioPmralA-nonlaicepS
)retpahC
HCTIWSTROBA)DxidneppAees(enoZesaeleRstrobA
ESAELERNAM)DxidneppAees(trobAsedirrevO
ECNELIShctiwSecneliSekilsnoitcnuF
TESERMETSYShctiwSteseRekilsnoitcnuF
ETAUCAVEhctiwSllirDekilsnoitcnuF
TIBIHNISAP)HxidneppAees(langiserPsedirrevO
NOMELBUORT)retpahCnoitarepOees(elbuorT=trohS
ALARALGRUB
ees(trohSnepOnomralAytiruceSsesuaC
)ExidneppA
Figure 3-1 Monitor Module Type Codes
To Next Page
Loading...
Need help?
General
