Notifier AFP-200

To Next Page

Analog Fire Panel

AFP-200

Installation Manual

Document 15511

10/14/2002 Rev:

15511:H2 ECN 02-436

Technical Manuals Online! - http://www.tech-man.com

Main Page

Default Chapter3
- Installation Precautions3
- Table of Contents4
About this Manual10
Section 1 System Overview14
- General Description14
- Features14
- Components15
- Main Assemblies17
- Optional Devices & Option Modules19
- Intelligent Detectors21
- Addressable Modules22
  - Overview22
  - Module Descriptions22
- End-Of-Line Devices24
  - Overview24
- Annunciation Modules24
- Peripheral Devices (TB4)26
- Specifications27
- Cabinet Dimensions28
  - Surface Mount with a BB-17 Battery Box28
  - Semi-Flush Mount29
Section 2 Installation30
- Preparing for Installation30
- Installation Checklist31
- Backbox Mounting32
- AC and DC Power Connections33
- DC Output Power Connections (TB1)35
- Output Circuits (TB2)35
  - Notification Appliance Circuits35
- Standard Relays (TB3)36
- Devices - Remote Printers and Crts (TB4)37
- Wiring a Signaling Line Circuit (SLC)41
- Option Module Installation61
Section 3 Programming65
- Overview65
  - Programming Methods65
  - In this Section65
- Getting Started66
- Program Change Options70
  - Overview70
- How to Enter Program Change71
- Status Change Options92
Section 4 Operation101
- Overview101
- The Membrane Panel102
- How to Operate the Control Panel106
- Control-By-Event Operation112
- Releasing Functions113
  - Overview113
  - How to Select Cross Zone Options113
- Releasing Functions114
- Intelligent Detector Functions115
  - Summary of Detector Functions115
  - Pre-Alarm Operation/Advanced Warning Addressable Combustion Sensing (AWACS™)115
- Time Functions116
- Read Status118
Appendix A Power Supply Calculations126
- Overview126
- Calculating the AC Branch Circuit126
- The Main Power Supply127
  - Current Limitations in Standby127
  - Current Limitations in Alarm - System Operation on Primary Power127
- Calculating the System Current Draw128
  - Overview128
  - How to Use Table 47 to Calculate System Current Draws128
- Calculating the Battery Size130
- Selecting and Locating Batteries131
- NFPA Battery Requirements131
Appendix B NFPA Applications132
- Section Overview132
  - Specific Requirements132
  - Additional Requirements132
- Central Station Fire Alarm Systems (Protected Premises)133
  - Installing a Notifier 911AC133
  - Installing a UDACT134
- NFPA 72 Auxiliary Fire Alarm System135
- Wiring a Remote Station Fire Alarm System136
- NFPA 72 Proprietary Fire Alarm Systems138
Appendix C Annunciators140
- Display140
  - ACS Mode140
  - Terminal Mode140
- Terminal Mode (LCD-80) Annunciation Interface (TB5 on CPU)140
- ACS Annunciation Interface (TB5 on CPU)141
  - Supported Modules141
- Annunciator Capacity141
  - Data Formats for Annunciator Address 1141
  - Data Formats at Annunciator Address 2141
- Terminal Mode EIA-485 Connections (TB5)144
- ACS Mode EIA-485 Connections145
- Power Connections for LCD and ACS Series Annunciators146
- ACS and LDM Series EIA-485 Connections147
Appendix D Releasing Applications148
- NFPA Standards148
- Programming Releasing Zones148
- Connecting Releasing Devices153
  - Connecting a Releasing Device to a Control Panel through an SLC Control or Relay Module154
  - Connecting an NBG-12LRA Agent Releasing Abort Station154
Appendix E Combination Fire/Burglary Applications157
- Overview157
- Installation157
- Programming159
- Operation160
Appendix F Wire Requirements161
Appendix G Pre-Alarm (AWACS™) Applications162
- Overview162
- Pre-Alarm Applications162
  - Pre-Alarm Alert Level162
  - Action Level Pre-Alarm Function163
- Pre-Alarm Programming163
Appendix H Special Zones167
- Overview167
- Presignal and Positive Alarm Sequence (PAS)167
  - Presignal167
  - Positive Alarm Sequence (PAS)167
- Time Control168
- NAC Code Types168
Appendix I Terminal Interface Protocol169
- General Description169
- Operating Modes169
- Using the CRT-2 for Read Status171
- Using the CRT-2 for Alter Status173
Appendix J Expansion Power Supplies177
- Overview177
  - AVPS-24 Audio/Visual Power Supply177
  - APS-6R Auxiliary Power Supply177
- Programming179
- Supply Calculations179
  - AVPS-24/AVPS-24E Calculations179
  - APS-6R Calculations180
- Installation180
  - Installing the AVPS-24/AVPS-24E180
  - Installing the APS-6R183
Appendix K UL Power-Limited Wiring Requirements186
- Overview186
- Typical Circuit with Nonpower-Limited and Power-Limited Wiring186
Appendix L U.S. Coast Guard & Lloyd's Register187
Appendix M CBE Programming189
- Purpose189
- Software Zones189
- How to Program CBE189
  - CBE Example 1189
  - CBE Example 2190
Appendix N External Battery Charger191
- Overview191
- Installation Requirements191
- Mounting the CHG-120191
  - Mounting the Charger into a CAB-X3 Series Cabinet191
  - Mounting the Charger into a Battery Box192
- Connecting the CHG-120194
  - Connecting a CHG-120 to the AFP-200194
  - Limited Warranty195

Table of Contents

Other manuals for Notifier AFP-200

Related product manuals