Novus N321 User Manual

NOVUS AUTOMATION 1/6
N321, N322, N323
TEMPERATURE CONTROLLERS
USER GUIDE
– V1.8x / V2.0x
1. SAFETY ALERTS
The symbols below are used in the device and throughout this
manual to draw the user’s attention to valuable information related to
device safety and use.
CAUTION:
Read the manual fully before
installing and operating the
device.
CAUTION OR HAZARD:
Risk of electric shock.
All safety recommendations appearing in this manual must be
followed to ensure personal safety and prevent damage to the
instrument or system. If the instrument is used in a manner other
than that specified in this manual, the device’s safety protections may
not be effective.
2. SUMMARY
1. SAFETY ALERTS ...................................................................................... 1
2. SUMMARY ................................................................................................. 1
3. INTRODUCTION ....................................................................................... 1
4. SPECIFICATIONS ..................................................................................... 1
5. ELECTRICAL CONNECTIONS ................................................................. 2
5.1 N321 MODEL ..................................................................................... 2
5.2 N322 MODEL ..................................................................................... 2
5.3 N323 MODEL ..................................................................................... 3
5.4 INSTALLATION RECOMMENDATIONS........................................... 3
6. OPERATION .............................................................................................. 3
6.1 LEVEL 1 – SETPOINT ADJUSTMENT LEVEL ................................. 3
6.2 LEVEL 2 – OPERATION MODE LEVEL ........................................... 3
6.3 LEVEL 3 – CALIBRATION LEVEL .................................................... 4
7. OPERATION .............................................................................................. 5
7.1 N321 MODEL: OPERATION ............................................................. 5
7.2 N322 AND N323 MODELS: OPERATION ........................................ 5
7.3 N322 AND N323 MODELS: ALARM FUNCTIONS ........................... 5
7.4 N323 MODEL: ALARM TIMER .......................................................... 5
8. CONFIGURATION PROTECTION ............................................................ 5
8.1 CONFIGURATION PROTECTION OPERATION ............................. 6
9. MASTER PASSWORD .............................................................................. 6
9.1 HOW TO USE YOUR MASTER PASSWORD .................................. 6
10. ERROR INDICATION ................................................................................ 6
11. SERIAL COMMUNICATION ...................................................................... 6
11.1 FEATURES ........................................................................................ 6
11.2 PARAMETER CONFIGURATION ..................................................... 6
11.3 COMMUNICATION PROTOCOL ...................................................... 6
11.4 REGISTER TABLE ............................................................................ 6
12. WARRANTY .............................................................................................. 6
3. INTRODUCTION
N321, N322, and N323 are temperature controllers for heating and
cooling. They are distinguished by the number of outputs available:
• N321: It has 1 output channel: OUT1.
• N322: It has 2 output channels: OUT1 and OUT2.
• N323: It has 3 output channels: OUT1, OUT2, and OUT3.
The models are subdivided by the type of temperature sensor
supported:
• NTC: Model accepting only the NTC sensor.
• Pt100: Model accepting only the Pt100 sensor.
• J/K/T: Model accepting only J, K and T sensors.
The features of each controller are in accordance with the purchase
order and are shown on the label attached to the body of the
controller itself.
Example of the label of an N323 model:
Figure 1 – Identification label
These models may have differences in power supply and the
availability of an RS485 communication channel.
4. SPECIFICATIONS
Sensor Input: The choice of sensor is made at the time of purchase
and shown on the controller identification label. There are three
options:
NTC Input:
Type: ............ NTC Thermistor, 10 kΩ @ 25 °C; β25/85 = 3435 K; 1 %
Measurement range: .............................. -50 to 120 °C (-58 to 248 °F)
Measurement accuracy: ....... 0.6 °C/F between -19.9 and 99.9 °C/F
............................................................................. 1 °C/F elsewhere
Pt100 Input:
Type: ............................................................................. Pt100,
α = 385
Measurement range: .............................. -50 to 300 °C (-58 to 572 °F)
Measurement accuracy: ........................ 0.2 % F.S. ± 2 °C @ 25 °C
J/K/T Input:
Measurement range J: ................................ 0 to 600 °C (32 to 999 °F)
Measurement range K: ............................ -50 to 999 °C (32 to 999 °F)

Novus N321 Specifications

General

Brand	Novus
Model	N321
Category	Controller
Language	English