Why is the media wrinkled when printed from my Oki C110?
If the media is wrinkled when printed by your Oki Printer, it may be moist from humidity or have water spilled on it, so replace it with new, dry media. The media feed roller or fuser unit could also be defective, so check them for damage. If you are using unsupported media, consult the 'Print Media' section.
Why does my Oki Printer have toner smudges or residual images?
If there are toner smudges or residual images on prints from your Oki Printer, one or more of the toner cartridges may be defective or installed incorrectly. Remove the toner cartridges and check for damage; replace any damaged cartridges.
How to troubleshoot image defects on Oki C110 Printer?
If you are experiencing image defects with your Oki Printer, start by cleaning the print head window. A leaking toner cartridge can cause defects, so remove the toner cartridges and check for damage. If a specific color is causing the issue, replace the corresponding toner cartridge. The imaging cartridge could also be defective, so remove it and check for damage, replacing it if necessary.
What to do if my Oki Printer power is not on?
If the Oki Printer power is not on, confirm that the power cord is correctly plugged into the outlet. If it is, plug another electrical appliance into the outlet to see whether it operates properly. Also, ensure the power switch is turned on. Finally, make sure the printer is connected to an outlet with a voltage or frequency that matches the printer specifications.
Why is my Oki C110 media misfeeding?
If the Oki Printer media is misfeeding, ensure the envelopes are loaded correctly in Tray 1 with the flaps facing down. If you're using unsupported media, consult the 'Print Media' section. Also, a dirty media feed roller can cause this issue, so clean the media feed roller.
Why does my Oki Printer take so long to print?
If printing takes too much time with your Oki Printer, it might be set to a slow printing mode. If you are using regular paper, make sure that the media type is set properly in the driver. The printer may be in power saving mode, which delays the start of printing. If the job is very complex, simply wait. Also, using a toner cartridge for a different region or an unapproved toner cartridge can slow down printing, so install a genuine Oki toner cartridge approved for your specific printer.
Why are colors not registering properly on Oki Printer?
If colors are not registering properly, or you notice colors are mixed or have page-to-page variation on your Oki Printer, it might be due to the imaging cartridge not being correctly seated. Remove the imaging cartridge and reinstall it. Also, one or more of the toner cartridges may be defective, so remove them and check for damage, replacing any damaged cartridges. Finally, the media could be moist from humidity, so replace it with new, dry media.
What causes Oki Printer to reset frequently?
If your Oki Printer is resetting or turning off frequently, begin by ensuring the power cord is correctly plugged into the outlet. Turn off the printer, confirm the cord is secure, and then turn the printer back on. If the issue continues, it may indicate a system error, in which case you should contact Technical Support with the error information.
Why is my Oki Printer's image too light?
If your Oki Printer is printing images that are too light or have low image density, several factors could be responsible. First, clean the print head window. If the issue persists, check if the media is moist and replace it with dry media. Additionally, the toner cartridge may be low; try replacing it. Defective toner cartridges can also cause this issue, so inspect them for damage. Finally, ensure the media type is correctly set in the printer driver, especially when printing labels, postcards, thick stock, or letterheads.
Why does my Oki C110 reset or turn off frequently?
If your Oki Printer resets or turns off frequently, confirm that the power cord is correctly plugged into the outlet. If the issue persists, contact Technical Support with the error information, as a system error may have occurred.
General| Color | Yes |
|---|---|
| Duplex printing | No |
| Maximum resolution | 600 x 1200 DPI |
| Time to first page (black, normal) | 13 s |
| Time to first page (color, normal) | 22 s |
| Print speed (black, normal quality, A4/US Letter) | 19 ppm |
| Print speed (color, normal quality, A4/US Letter) | 5 ppm |
| Internal memory | 16 MB |
| Sound power level (standby) | 29 dB |
| Sound pressure level (printing) | 51 dB |
| Total input capacity | 200 sheets |
| Total output capacity | 100 sheets |
| Maximum print size | 216 x 356 mm |
| ISO A-series sizes (A0...A9) | A4, A5 |
| ISO B-series sizes (B0...B9) | B5 |
| Maximum ISO A-series paper size | A4 |
| Supported media weight(s) | 60/209 g/m² |
| Compatible operating systems | Windows 2000 / XP / XP x64 / Vista (32 bit) / Vista (64 bit) / Server 2003 / Server 2003 x64 / Server 2008 / Server 2008 x64 |
| Maximum operating temperature range (T-T) | 10 - 35 °C |
| Recommended operating temperature range (T-T) | 15 - 25 °C |
| Maximum duty cycle | 250 pages per month |
| Sustainability certificates | ENERGY STAR |
| Power consumption (printing) | 440 W |
| Power consumption (PowerSave) | 14 W |
| Storage temperature (T-T) | -20 - 40 °C |
| Storage relative humidity (H-H) | 10 - 95 % |
| Operating relative humidity (H-H) | 15 - 85 % |
Weight and Dimensions| Dimensions (WxDxH) | 396 x 380 x 275 mm |
|---|
To Next Page
