- 86 -
5. Management / Setting the Printer
*1 Factory default setting values are different according to the country or region.
*2 The values are displayed with the unit set in [Admin Setup] > [Tray Setup] > [Unit of Measurement].
• Menu > System Adjust
• Menu > Print Adjust > Print Position Adjust
Tray1 Config Paper Size Cassette Size Selects a paper size for Tray 1.
X Dimension 210 millimeter
or 8.5 inch *
2
Sets a width of a custom paper for Tray 1.
Y Dimension 297 millimeter
or 11.0 inch *
2
Sets a length of a custom paper for Tray 1.
Media Type Plain Selects a paper type for Tray 1.
Media Weight Light Selects a paper weight for Tray 1.
Legal Paper Legal14 Sets a legal paper size for Tray 1.
Other Size 16K
(184 x 260 mm
) [SEF]
Sets other standard paper size for Tray 1.
Tray2/3/4/5
Config *
* Displayed
when an
optional tray is
installed.
Paper Size Cassette Size Selects a paper size for Tray 2/3/4/5.
X Dimension 210 millimeter
or 8.5 inch *
1
Sets a width of a custom paper for Tray 2/3/4/5.
Y Dimension 297 millimeter
or 11.0 inch *
1
Sets a length of a custom paper for Tray 2/3/4/5.
Media Type Plain Selects a paper type for Tray 2/3/4/5.
Media Weight Light Selects a paper weight for Tray2/3/4/5.
Legal Paper Legal14 Sets a legal paper size for Tray 2/3/4/5.
Other Size 16K
(184 x 260 mm
) [SEF]
Sets other standard paper size for Tray 2/3/4/5.
Paper Feed Tray1 Selects a paper tray.
Auto Tray Switch On Sets whether to enable the auto tray switching function.
Tray Sequence Down Sets the priority of tray order for auto tray selection/auto tray
switching.
Duplex Last Page Skip Blank
Page
When [Skip Blank Page] is selected, the last page of an odd-
numbered duplex print job is printed in simplex.
When [Always Print] is selected, the printer always prints a
document in the duplex mode if the duplex mode is selected.
Some applications may not work properly.
Item Factory
Default
Description
Power Save Time 1 minute Sets how many minutes the printer waits before activating the
power save mode.
Sleep Time 15 minutes Sets the time to switch from the power save mode to the
sleep mode.
Item Factory
Default
Description
Auto Power Off Time 4 hours Sets the time to switch from the standby mode to the power
off mode.
Silent Mode On Specifies a print preparation operation when entering standby
status from Sleep mode.
[On]: It is quiet as there is no print preparation.
[Off]: There is a rotation noise of the image to perform print
preparation but you can start first printing early.
Clearable Warning ONLINE Sets the timing for deletion of clearable warnings.
Auto Continue Off Sets whether to recover the printer automatically when a
memory overflow or tray requesting occurs.
Manual Timeout 60 seconds Sets how many seconds the printer waits for the paper to be
fed from the manual paper tray.
Timeout InJob 40 seconds Sets how many seconds the printer will wait before force
printing a job after the data stops coming.
Timeout Local 40 seconds Sets how long each port is left opened after a job is complete.
(The network is excluded.)
Timeout Network 90 seconds Sets how long the network port is left opened after a job is
complete.
Low Toner Continue Sets whether to continue or stop printing when a low on toner
error occurs.
Print Mode w/o Color Toner Alarm Specifies the action when there is an empty color toner.
[Alarm]: The machine stops without printing the color print
job. Replace the toner cartridge with a new one.
[Cancel]: Cancels a new color print job automatically.
Replace the toner cartridge with a new one.
Jam Recovery On Sets whether the printer will attempt to re-print any pages lost
due to a paper jam once the jam has been cleared.
Error Report Off Sets whether to print out the error details when an internal
error occurs.
Hex Dump Execute Prints out the data received from the host computer in
hexadecimal dump format.
Turning off the power switches the printer to the normal print
mode from the HEX Dump mode.
Item Factory
Default
Description
To Next Page
Loading...
Need help?
General
