To Next PageTo Next PageHow to fix Olympus U-TR30-2 when the bulb does not light?
If the Olympus Microscope bulb does not light, ensure the power cord of the BX-UCB (or TH4) is firmly plugged into the power outlet. Also, check that the main switch of the BX-UCB (or TH4) is set to “I” (ON). Verify that the transmitted light illumination is correctly set, and if the bulb is burnt out, replace it with a new specified bulb.
What to do if Olympus U-TR30-2 Microscope visibility is poor and the image is not sharp?
If your Olympus Microscope visibility is poor, the image isn't sharp or the contrast is poor, ensure you're using the specified objective and eyepieces. Clean any dirt or dust from the specimen. Also, check that the aperture iris diaphragm is set properly.
How to fix an obscured or unevenly illuminated field of view on my Olympus U-TR30-2 Microscope?
If the field of view is obscured or not evenly illuminated on your Olympus Microscope, check the following: 1. Ensure the light path selector lever of the trinocular tube is correctly set according to the observation method. 2. Verify the revolving nosepiece is correctly mounted. 3. Center the aperture iris diaphragm. 4. Open the field iris diaphragm until it circumscribes the field. 5. Make sure the bulb is correctly mounted by pushing the pins of the halogen bulb all the way to the stop position.
How to remove dirt or dust visible in the field of view of my Olympus Microscope?
If you see dirt or dust in the field of view of your Olympus Microscope, the dirt/dust may be on an eyepiece. Clean it thoroughly.
What to do if the specimen cannot be brought into focus on Olympus U-TR30-2 Microscope?
If the specimen cannot be brought into focus on your Olympus Microscope, adjust the hardware (or software) lower limit to an optimum height. If this does not solve the problem, re-place the specimen within the focusing range.
Why is the field of view dark on my Olympus U-TR30-2 even when the bulb is on?
If the field of view remains dark even when the bulb operates on your Olympus Microscope, check if the aperture and field iris diaphragms are opened wide enough. Ensure the light path selector lever of the trinocular tube is in the correct position ( or ).
What causes the bulb to intermittently light and go out on an Olympus U-TR30-2 Microscope?
If the bulb in your Olympus Microscope intermittently lights and goes out, it might be nearly burnt out, so replace it. Also, check all cords and connectors to ensure they are securely connected.
Why is one side of the image blurred on my Olympus U-TR30-2 Microscope?
If one side of the image appears blurred or wavers on your Olympus Microscope, ensure the specimen is correctly placed. Also, check that the revolving nosepiece is correctly mounted. If a heavier weight than restricted (3 kg) is applied to the revolving nosepiece mount area, reduce the number of modules to reduce the weight below the restriction.
Why does the Olympus Microscope bulb burn out so quickly?
If the bulb burns out almost immediately in your Olympus Microscope, ensure you are using the correct bulb type.
Why doesn't the field of view match between both eyes on my Olympus U-TR30-2?
If the field of view of one eye does not match that of the other on your Olympus Microscope, adjust the interpupillary distance and the diopter. Ensure that the eyepieces used on the left and right sides are the same type. When looking into eyepieces, do not stare at image from the beginning but see the overall field of view. It is sometimes recommended to turn your eyes away from the eyepieces, look far off and look into the eyepieces again.
General| Brand | Olympus |
|---|---|
| Model | U-TR30-2 |
| Category | Microscope |
| Language | English |
Explains the meaning of various safety symbols used in the manual.
Identifies and labels the parts of the BXFMA-F motorized illuminator and focusing unit.
Details on the TH4 power supply unit for the system.
Describes the operation of BF/DF switching, diaphragm control, and focus adjustment.
Steps to adjust the motorized focusing unit, including hardware limits.
Procedures for adjusting interpupillary distance, diopter, and using eye shades.
