To Next PageTo Next PageWhat to do if an error occurs during the update process of my Onkyo Receiver?
If an error occurs during the update process of your Onkyo Receiver, disconnect the AC power cord, reconnect it, and then try the update again.
What to do if my Onkyo Receiver shows an error because of a wrong selection of input sources?
If an error occurs on your Onkyo Receiver due to a wrong selection of input sources, turn the receiver off and then on again. After restarting, retry the update.
Why does my Onkyo Receiver display “Error!! *-11, *-13, *-21, *-28”?
If your Onkyo Receiver displays “Error!! *-11, *-13, *-21, *-28”, this indicates an internet connection error. Here's what to check: * Ensure the IP address, subnet mask, gateway address, and DNS server are configured correctly. * Verify that your router is powered on. * Confirm the receiver and router are connected with an Ethernet cable. * Check your router's configuration using its instruction manual. If your network limits connections, disconnect other devices. Contact your Internet Service Provider (ISP) if needed. If your modem isn't a router, you'll need one. Depending on your network, proxy server configuration may be necessary. Contact your ISP for guidance. If issues persist, the DNS or proxy server might be down temporarily; contact your ISP.
How to fix “Error!! *-10, *-20” on Onkyo Receiver?
If your Onkyo Receiver displays the error message “Error!! *-10, *-20”, it means the Ethernet cable was not detected. To solve this, reconnect the cable properly.
What to do if my Onkyo TX-8050 says 'Error!! *-** No media'?
If the Onkyo Stereo Receiver displays an 'Error!! *-** No media' message, it could be due to several reasons. First, ensure that the USB flash memory or USB cable is correctly connected to the USB port, and if the USB storage device requires external power, make sure it's powered on. Alternatively, the receiver might not be detecting the firmware file because it's missing from the root folder of the USB device or because the firmware file is not intended for your specific model. In this case, download the correct file from the support page of the Onkyo website, carefully following the provided instructions. If the problem continues, contact Onkyo Support and provide the error code. As an additional step, you can also retry the update procedure from the beginning.
How to fix Onkyo TX-8050 tone controls not working?
If the tone controls on your Onkyo Stereo Receiver aren't working, it might be because the DIRECT function is enabled, or the PURE AUDIO button is lit. To resolve this, press the [AUDIO] or [PURE AUDIO] button to turn the function off.
Amplifier and Power| power output at 8 ohms | 80 W + 80 W |
|---|---|
| power output at 6 ohms | 100 W + 100 W |
| dynamic power at 3 ohms | 180 W + 180 W |
| dynamic power at 4 ohms | 160 W + 160 W |
| dynamic power at 8 ohms | 100 W + 100 W |
Audio Performance| total harmonic distortion + noise | 0.08% (20 Hz–20 kHz, Half power) |
|---|---|
| damping factor | 60 (1 kHz, 8 ohms) |
| frequency response | 5 Hz–100 kHz (+1 dB, -3 dB) |
| tone control bass | ±10 dB, 50 Hz |
| tone control treble | ±10 dB, 20 kHz |
| signal-to-noise ratio line | 106 dB (IHF-A) |
| signal-to-noise ratio phono MM | 80 dB (IHF-A) |
Input and Output| input sensitivity and impedance line | 200 mV/47 k-ohms |
|---|---|
| phono MM input sensitivity and impedance | 2.5 mV/47 k-ohms |
| rated RCA output level and impedance rec out | 200 mV/2.2 k-ohms |
| maximum RCA output level and impedance rec out | 2.0 V/2.2 k-ohms |
| phono overload | 60 mV (MM, 1 kHz, 0.5%) |
| speaker impedance | 4 ohms–16 ohms (A or B), 8 ohms–16 ohms (A + B) |
Video Section| input sensitivity/output level and impedance composite | 1.0 Vp–p/75 ohms |
|---|
Tuner Section| FM tuning frequency range | 87.5 MHz–107.9 MHz |
|---|---|
| AM tuning frequency range | 530 kHz–1, 710 kHz |
General Specifications| power supply | AC 120 V~, 60 Hz |
|---|---|
| power consumption | 3.1 A |
| dimensions | 17 1/8˝ x 5 7/8˝ x 12 15/16˝ (435 x 149.5 x 328 mm) |
| weight | 19.0 lbs. (8.6 kg) |
Carton Specifications| carton dimensions | 22 1/2˝ x 10 3/8˝ x 16 1/2˝ (572 x 264 x 419 mm) |
|---|---|
| carton weight | 24.3 lbs. (11.0 kg) |
Critical warnings and cautions for safe operation.
Key safety guidelines for using the apparatus.
Important precautions before connecting speakers.
Step-by-step guide on connecting speaker cables.
How to connect a powered subwoofer to the receiver.
Steps to set speaker impedance on the receiver.
How to connect a power amplifier for preamp use.
Instructions for connecting FM and AM antennas.
General information about connecting AV components.
How to connect Onkyo components using RI interface.
How to connect a component for recording audio/video.
How to record the selected input source to a component.
How to record audio and video from different sources simultaneously.
How to tune into AM and FM radio stations.
How to connect an iPod/iPhone to the receiver's USB port.
How to play music files from an iPod/iPhone.
How to play music files from a USB device.
How to connect to and listen to internet radio.
How to use the vTuner Internet Radio service.
How to play music files from a computer or media server.
How to listen to internet radio stations via browser.
Diagram showing network connection setup.
Requirements for Ethernet and network setup.
Requirements for media servers and playback.
List of supported audio file formats.
General information and setup for using the Onkyo Dock.
How to use an RI Dock for iPod/iPhone playback.
How to control iPod/iPhone with UP-A1 or RI Dock.
General procedure for changing advanced settings.
Step-by-step example of setting Intelli Volume.
How to assign digital audio inputs to selectors.
Settings related to Zone 2 audio output and controls.
Procedures for updating receiver firmware.
How to set Intelli Volume and change input names.
Manual configuration of receiver network settings.
Settings for speaker impedance, AM/FM frequency, and Auto Standby.
Steps to update firmware using a network connection.
Steps to update firmware using a USB storage device.
Troubleshooting common firmware update errors.
Error codes and solutions for network updates.
Error codes and solutions for USB updates.
Troubleshooting for no sound or quiet audio issues.
Troubleshooting common problems with USB device playback.
Troubleshooting server and internet radio connectivity.
