To Next PageTo Next Page
Need help?Do you have a question about the Onkyo TX-NR900 and is the answer not in the manual?
General| Channels | 7.1 |
|---|---|
| Network Connectivity | Ethernet, Wi-Fi |
| Room Calibration | AccuEQ |
| Component Video Inputs | 3 |
| Component Video Outputs | 1 |
| Digital Audio Inputs (Optical) | 2 |
| Digital Audio Inputs (Coaxial) | 2 |
| Analog Audio Inputs | 6 |
| Input Sensitivity/Impedance | 200 mV / 47 kOhms |
| Video Inputs/Outputs (Composite) | 4 Inputs, 1 Output |
| Phono Input | Yes |
| HDMI Outputs | 2 |
| Audio Formats Supported | Dolby TrueHD, DTS-HD Master Audio |
| Video Formats Supported | 1080p, 4K |
| Streaming Services | Spotify, Pandora, Tidal |
| THX Certified | Yes |
| Frequency Response | 10 Hz - 100 kHz |
| Multi-room Output | Zone 2 |
| Weight | 11.0 kg |
| Power Output | 130 W per channel (8 ohms) |
| Total Harmonic Distortion | 0.08% (1 kHz, 1 W) |
Identifies the specific AV receiver model covered by the manual.
Critical safety warning regarding components vital for fire/shock protection.
Details the technical specifications of the receiver's amplification circuitry.
Lists the technical specifications for the FM and AM tuner performance.
Covers general specifications like power supply, consumption, dimensions, and weight.
Procedure for replacing fuses, emphasizing correct type and rating for safety.
Steps to reset the unit to factory settings, including memory initialization.
Safety check procedure for U.S. models after service, focusing on insulation resistance.
Instructions for setting the correct voltage for worldwide models to match local power supplies.
Component and soldering layout for the volume control PC board.
Layout for the headphone terminal PC board, showing component and soldering sides.
Details the front video input PC board layout, including component and soldering views.
Shows the layout for the front optical input PC board, component and soldering sides.
Shows the component and soldering sides of the component video PC board.
Shows the wiring connections to the preamplifier PC board.
Wiring connections to the AC inlet terminal PC board.
Wiring connections to the primary circuit PC board.
Wiring connections to the front/center channels driver amplifier board.
Wiring connections to the power amplifier PC board.
Wiring connections to the surround channels driver amplifier board.
Wiring connections to the DSP circuit PC board.
Wiring connections to the preamplifier PC board.
Wiring connections to the front optical input PC board.
Wiring connections to the main connector PC board.
Wiring connections to the video terminal PC board.
Wiring connections to the RS232 terminal PC board.
Component and soldering layout for the volume control PC board.
Layout for the headphone terminal PC board, showing component and soldering sides.
Details the front video input PC board layout, including component and soldering views.
Shows the layout for the front optical input PC board, component and soldering sides.
Soldering side layout for the front/center speaker terminal PC board.
Soldering side layout for the surround speaker terminal PC board.
Soldering side layout for the fan drive circuit PC board.
Soldering side layout for the bias selector relay PC board.
Soldering side layout for the thermal detector PC board.
Soldering side layout for the primary circuit PC board.
Soldering side layout for the power switch PC board.
Component parts layout for the main connector PC board.
Component parts layout for the RS232 terminal PC board.
Component parts layout for the main connector PC board.
Component parts layout for the RS232 terminal PC board.
Instructions for entering and navigating the unit's test modes via FL tube display.
Procedure to confirm voltage sensor readings and relay operation under specific test conditions.
Confirms current detection by measuring output levels with different loads and checks relay behavior.
Tests fan operation speed under various input signal and resistor connection conditions.
Procedure to adjust idling current for front/center and surround channels using trimming resistors.
Verifies speaker relays turn ON after power-up and OFF when power is switched off.
Checks speaker relay behavior when DC voltage is applied to the MULTI-CH INPUT.
