Onkyo TX-SR800 User Manual

Contents
Thank you for purchasing the Onkyo AV Receiver.
Please read this manual thoroughly before making
connections and plugging in the unit. Following the
instructions in this manual will enable you to obtain
optimum performance and listening enjoyment from
your new AV Receiver. Please retain this manual for
future reference.
TX-SR800
Appendix 73
Remote controller 61
Setup and operation 29
Before using 2
AV Receiver
Instruction Manual
Facilities and connections 8
E

Onkyo TX-SR800 Specifications

Amplifier Specifications

continuous average power output	100 W per channel min. RMS at 8 Ω, 130 W min. RMS at 6 Ω
continuous power output (DIN)	135 W at 6 Ω
maximum power output (EIAJ)	160 W at 6 Ω
dynamic power output (stereo)	2 × 250 W at 3 Ω, 2 × 210 W at 4 Ω, 2 × 130 W at 8 Ω
total harmonic distortion	0.08% at rated power
IM distortion	0.08% at rated power
damping factor	60 at 8 Ω

Input Specifications

phono input sensitivity and impedance	2.5 mV, 50 kΩ
line input sensitivity and impedance	200 mV, 50 kΩ
multichannel input sensitivity and impedance	200 mV, 50 kΩ
subwoofer input sensitivity and impedance	36 mV, 50 kΩ
coaxial input sensitivity and impedance	0.5 Vp-p, 75 Ω
video input sensitivity and impedance	1 Vp-p, 75 Ω

Output Specifications

rec out level and impedance	200 mV, 470 Ω
pre out level and impedance	1 V, 470 Ω
video output level and impedance	1 Vp-p, 75 Ω
component video output level and impedance	1 Vp-p, 75 Ω (Y), 0.7 Vp-p, 75 Ω (PB, PR)

Frequency Response & Tone Control

frequency response	10 Hz to 100 kHz : +1/–3 dB
RIAA deviation	20 Hz to 20 kHz : ±0.8 dB
bass tone control	±10 dB at 50 Hz
treble tone control	±10 dB at 20, 000 Hz
signal-to-noise ratio (direct) phono	80 dB (IHF A, 5 mV input)
signal-to-noise ratio (direct) line	110 dB (IHF A, 0.5 V input)

FM Tuner Specifications

FM tuning range	87.5–108.0 MHz (USA & Canadian models), 87.50–108.00 MHz (Other models)
usable sensitivity mono	11.2 dBf, 1.0 µV (75 Ω IHF)
usable sensitivity stereo	17.2 dBf, 2.0 µV (75 Ω IHF)
50 dB quieting sensitivity mono	17.2 dBf, 2.0 µV (75 Ω)
50 dB quieting sensitivity stereo	37.2 dBf, 20 µV (75 Ω)
capture ratio	2.0 dB
image rejection ratio	40 dB (USA & Canadian models), 85 dB (Other models)
IF rejection ratio	90 dB
signal-to-noise ratio mono	76 dB
signal-to-noise ratio stereo	70 dB
alternate channel attenuation	55 dB
selectivity	50 dB (DIN)
AM suppression ratio	50 dB
total harmonic distortion mono	0.2%
total harmonic distortion stereo	0.3%
frequency response	30 Hz–15 kHz, ±1.0 dB
stereo separation	45 dB at 1 kHz

AM Tuner Specifications

AM tuning range	530 to 1, 710 kHz (USA & Canadian models), 522 to 1, 611 kHz (Some Asian and Australian models), 522 to 1, 611 kHz (Worldwide models)
usable sensitivity	30 µV
image rejection ratio	40 dB
IF rejection ratio	40 dB
signal-to-noise ratio	40 dB
total harmonic distortion	0.7%

General Specifications

power supply	AC 120 V, 60 Hz (USA & Canadian models), AC 230–240 V, 50 Hz (Australian models), AC 220–230 V, 50/60 Hz (Some Asian models), AC 220–230 and 120 V switchable, 50/60 Hz (Worldwide models)
power consumption	8.1 A (USA & Canadian models), 655 W (Other models)
dimensions	435 × 175 × 459 mm
weight	35.9 lbs. (USA & Canadian models), 17.3 kg (Other models)

Remote Controller Specifications

transmitter	Infrared
signal range	Approx. 16 ft., 5 meters
power supply	Two “AA” batteries (1.5 V × 2)