ORTEA SpA MAT200 aug21
4 / 24
1 INTRODUCTION
This Manual contains the information necessary to ensure correct operation of the unit, efficient maintenance program,
avoidance of incorrect use and safety for the personnel involved with the unit performance. The voltage stabilisers described
in this manual must be used exclusively for the purpose for which they have been designed and manufactured. Installation
must be done according to the instructions provided with this handbook.Any other use has to be considered as inappropriate
and therefore dangerous. The Manufacturer shall not to be held liable for any damage to people and belongings due to
incorrect use or installation. In case of doubt and for any other necessity, please contact the nearest authorised Service
Centre. This Manual is as an integral part to the unit and the instructions therein must be carefully followed. File this manual
and all the attached documentation for further consultation in a place available and known to the user and the maintenance
personnel and keep it for the entire life of the unit.
1.1 INFORMATION PROPERTY
This Manual (including any attached document) is covered by copyright and the Manufacturer maintains all the reserved
rights. It is compulsory to inform the Manufacturer’s Head Office and ask for authorisation before proceeding with any
release or reproduction. The Manufacturer shall not be held liable or responsible in any way for unauthorised copies,
alterations or additions to the text or to the illustrated parts of this document. Any modification involving company logo,
certification symbols, names and official data is strictly forbidden.
In order to obtain better performance, the product described in the present handbook can be altered at any date and
without prior notice.
1.2 REFERENCE NORMATIVE
The units described in this Manual are designed and built in compliance with:
2014/35/EU (Low Voltage European Directive)
2014/30/EU (Electromagnetic Compatibility European Directive)
applicable parts of the EN61439-1/-2 (Low-voltage switchgear and controlgear assemblies) Harmonised Standard
Furthermore, the Manufacturer’s Managing System is compliant and duly approved according to:
ISO9001:2015 (Quality)
ISO14001:2015 (Environmental issues)
ISO45001:2018 (Health & Safety at work)
WARNING INFORMATION AND INSTRUCTIONS PROVIDED BY THIS MANUAL ADD TO AND NEITHER REPLACE NOR AMEND
ANY STANDARDS, REGULATIONS, DECREES, DIRECTIVES OR LAWS CONCERNING ENVIRONMENTAL AND SAFETY AT WORK
AWARENESS ENFORCED BOTH INTERNATIONALLY AND IN THE COUNTRY OF INSTALLATION.
1.3 DEFINITIONS
WARNING MESSAGE RELEVANT TO POTENTIALLY HAZARDOUS SITUATIONS WHICH MIGHT INDUCE MINOR INJURIES IF
IGNORED OR NEGLECTED. THE SAME SIGNAL CAN BE USED TO HIGHLIGHT HAZARDS WHICH MIGHT CAUSE DAMAGE TO THE
UNIT OR TO POINT OUT IMPORTANT INFORMATION.
DANGER MESSAGE RELEVANT TO POSSIBLE OR PROBABLE HAZARDOUS SITUATIONS WHICH MIGHT INDUCE SERIOUS OR
EVEN FATAL HARM IF IGNORED OR NEGLECTED.
Note Additional information to better understand the unit operation.
2 ENVIRONMENTAL NOTES
Note Units weighing more than 2000kg do not enter the scope of the 2012/19/EU WEEE Directive (Waste of
Electric and Electronic Equipment) as they can be identified as large fixed industrial equipment. Nevertheless,
although they do not bear the relevant symbol on their nameplates, it is recommendable to follow the Directive’s
guidelines concerning a responsible disposal at the end of their working life.
With reference to the 2012/19/EU WEEE Directive (Waste of electric and electronic equipment), please be aware
that the products described in this manual have been produced after August 13th 2015. When applicable, the
WEEE symbol (beside) on the product label and / or accompanying documents means that used electrical and
electronic equipment must not be mixed with general household or municipal waste. At the end of their useful
life, these products must be disposed of via suitable channels. Please refer to the current legislation in force in
the Country of installation.
Professional users in the European Union must contact their dealer or supplier for further information.
The symbol is only valid in the European Union (EU). For disposal in countries outside of the European Union please contact
the local authorities or dealer and ask for the correct method of disposal.
Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human
health and the environment, which could otherwise arise from inappropriate waste handling.
The product does not contain CFCs, HCFCs, asbestos, fuel, PCB, PCT, liquids or gaseous substances. Please recycle the
packaging materials (cardboard and/or wood). At the end of the service, before disposing of the unit, remove the nameplate
and make the appliance unusable by cutting the internal connections.
To Next Page
Loading...