Owon SDS1104 User Manual

SDS1000 Series
Digital Storage Oscilloscope
User Manual
www.owon.com.cn

Owon SDS1104 Specifications

General

Bandwidth	100 MHz
Channels	4
Sample Rate	1 GSa/s
Memory Depth	10Mpts
Vertical Sensitivity	2 mV/div to 10 V/div
Timebase Range	5 ns/div to 50 s/div
Trigger Types	Edge, Pulse, Video, Slope, Alternate
Math Functions	+, -, *, /, FFT
Trigger Modes	Auto, Normal, Single
Display	7 inch TFT LCD
Vertical Resolution	8 bit
Display Resolution	800 x 480
Interface	USB Host, USB Device, LAN
Input Impedance	1MΩ
Input Voltage Range	400 V (DC + AC peak)
Record Length	10 Mpts

Summary

General Warranty

General Safety Requirements

Fire and Personal Injury Precautions

Precautions to prevent fire and personal injury during operation, including power, grounding, and ventilation.

Safety Terms and Symbols

Safety Terms Definitions

Definitions of safety terms like Warning, Caution, and Danger used in the manual.

Safety Symbols and Meanings

Explanation of safety symbols found on the product and their meanings.

Electrical Safety Precautions

Quick Start Guide

Front Panel Overview

Description of the oscilloscope's front panel layout, buttons, and controls.

Rear Panel Overview

Control Area Description

User Interface Introduction

Understanding Display Indicators

Initial Instrument Inspection

Functionality Verification

Probe Compensation Adjustment

Setting Probe Attenuation

Safe Probe Usage

Self-Calibration Procedure

Vertical System Controls

Vertical System Operation

Horizontal System Controls

Horizontal System Operation

Trigger System Controls

Triggering Basics

Single Trigger Modes

Edge Trigger Configuration

Video Trigger Configuration

Alternate Trigger Modes

Advanced User Guidebook

Vertical System Settings

How to configure and adjust vertical system parameters.

Horizontal System Settings

How to configure and adjust horizontal system parameters.

Trigger System Settings

How to configure and adjust trigger system parameters.

Sampling and Display Settings

How to set sampling modes and display options.

Waveform Save and Recall

Procedures for saving and recalling waveform data.

Auxiliary System Function Setup

Instrument Firmware Update

Automatic Measurement

Cursor Measurement

Executive Button Functions

Vertical Coupling and Inversion

Adjusting Probe Attenuation

Measuring Current via Voltage Drop

Mathematical Manipulation Function

Waveform Calculation

Using FFT Function

FFT Window Selection

Vertical Position and Scale Knobs

Horizontal Position and Scale Knobs

Wave Zoom Functionality

Trigger System Overview

Single Trigger Modes

Video Trigger Modes

Alternate Trigger Modes

Sampling and Display Settings

XY Format Operation

Counter Functionality

Save and Recall Waveforms

Saving Configurations and Images

USB Disk Requirements and Formatting

Auxiliary System Function Setup

Probe Checking Procedure

Instrument Firmware Update

Automatic Measurement Parameters

Automatic Time Measurement Parameters

Other Measurement Types

Cursor Measurement Guide

FFT Mode Cursor Measurement

Executive Button Functions (Autoset)

Executive Button Functions (Run/Stop, Copy)

Demonstration Examples

Measuring a Simple Signal

Example demonstrating measurement of basic signal properties like frequency.

Amplifier Gain Measurement

Example showing how to measure amplifier gain using signal amplitudes.

Capturing a Single Signal

Analyzing Signal Noise

X-Y Function Application

Video Signal Triggering

Video Field Trigger Setup

Troubleshooting Guide

No Display or Waveform

Solutions for issues where the oscilloscope has no display or no waveform.

Unstable Waveform Display

Solutions for problems causing an unstable or jittery waveform display.

Incorrect Amplitude Readings

Troubleshooting steps for inaccurate voltage amplitude measurements.

Slow Display or Response Issues

Solutions for slow display updates or unresponsive controls.

Technical Specifications

Performance Characteristics

Key performance specs like bandwidth, acquisition, and input characteristics.

Horizontal System Specifications

Specifications related to the oscilloscope's horizontal system.

Vertical System Specifications

Specifications related to the oscilloscope's vertical system.

Measurement Specifications

Trigger Specifications

General Display Specifications

Probe Compensator Output

Power and Environment Specifications

Mechanical Specifications

Appendix

Standard Accessories List

A list of standard accessories included with the oscilloscope.

General Care and Cleaning

Guidelines for the general care and maintenance of the instrument.

Cleaning Instructions