Owon SDS7102V - How to Implement the Probe Compensation

To Next Page

To Previous Page

Section 1: General Information

1.4 General Technical Specifications

Table 2: General specifications

Display

Display Type 8” Colored LCD (Liquid Crystal Display)

Display Resolution 800 (Horizontal) × 600 (Vertical) Pixels

Display Colors 65536 colors, TFT screen

Output of the Probe Compensator

Output Voltage

(Typical )

About 5V, with the Peak-to-Peak voltage ≥1MΩ.

Frequency (Typical ) Square wave of 1KHz

Power

Mains Voltage

100～240 VAC RMS, 50/60Hz, CAT II

Power Consumption

< 18W---SDS6062(V)

< 24W---other models

Fuse 2A, T grade, 250V

Battery (optional)

Cell:558792 4000mAh/3.7V

Pack:2s2p 7.4V/8000mAh

Mechanical Specifications

Dimension 340mm× 155mm×70mm (L*H*W)

Weight About 1.82 kilogram

Interval Period of Adjustment:

One year is recommended for the calibration interval period.

Main Page

Table of Contents4
General Safety Summary6
Section 1: General Information9
Introduction9
Accessories Supplied9
Technical Specifications9
Table 1: Specifications10
General Technical Specifications15
Table 2: General Specifications15
Declaration of Conformity16
Section 2: Installation17
Performing the General Inspection17
Operating Environment17
Storage and Transport17
Table 3: Environment17
Packaging18
Tagging for Service18
Power Supply Requirement18
Cleaning Requirements18
Section 3: Test and Calibration19
Equipment for Testing19
Test Standard19
Inspection Items and Methods19
Figure 1: Connection of Sweep Rate and Error Inspection20
Figure 2: Waveform of Sweep Rate and Error Inspection20
Figure 3: Connection of Voltage Division and Error Inspection21
Figure 4: Connection of Voltage Measurement and Error Inspection21
Figure 5: Connection of Transient Response Inspection22
Figure 6: Waveform of Transient Response Inspection22
Figure 7: Connection of Vertical Movement Range Inspection23
Figure 8: Connection of Input Impedance Inspection24
Figure 9: Connection of Maximum Input Voltage Testing24
Section 4: Debugging and Calibration26
Brief Introduction26
Tools and Devices26
The Interval Time to Calibration26
Auto-Calibration26
Attenuation Compensation Capacitance and Resistance Calibration26
Figure 10: Attenuation Switch27
Figure 11: Connection of Calibrating the Probe in the CH127
Figure 12: Displayed Waveforms of the Probe Compensation27
Figure 13: Adjust Probe27
Figure 14: the Position of the Attenuation Compensation Capacitance28
Figure 15: the Position of the Attenuation Compensation Resistance29
Section 5: Maintenance30
Brief Introduction30
Preparation and Safety Event30
Circuit Diagram30
Figure 16: SDS Series Block Diagram30
Removal and Installation Procedures32
Figure 17: the Schematic Circuit Diagram of the Power Supply32
Figure 18: Loosen the Screws of Battery Box32
Figure 19: Remove the Battery Box Cover32
Figure 20: Remove the Ground Connection33
Figure 21: Remove the Screws of Rear Panel34
Figure 22: Unsnap the Rear Panel (1)34
Figure 23: Unsnap the Rear Panel (2)34
Figure 24: Disconnect the Rear Panel and Remove the Battery Box Container35
Figure 25: Remove Power Supply Board35
Figure 26: Screws and Cables of the Adapter Plate36
Figure 27: Remove the Adapter Plate36
Figure 28: Remove the Chassis37
Figure 29: Fan Power Cable of the Chassis37
Figure 30: Install the Chassis (1)38
Figure 31: Install the Chassis (2)38
Figure 32: Screws Secure the Fan39
Figure 33: Screws Secure the Main Board39
Figure 34: Remove the Main Board40
Examination and Maintenance42
Figure 35: Troubleshooting Procedure (1)42
Figure 36: Troubleshooting Procedure (2)43
Section 6: Replaceable Parts44
Replaceable Parts List44
Order Information44
Table 4: Replaceable Parts List44

Owon SDS7102V - How to Implement the Probe Compensation

Table of Contents

Other manuals for Owon SDS7102V

Related product manuals