– 150 –
Chapter 6 Menu Operations — Menu list
[CARD FUNCTIONS]
Congure the settings regarding reading/writing of the scene les and user les to SD memory cards.
Item Description of settings
[SCENE FILE] Loads scene les from an SD memory card or saves them to an SD memory card.
[LOAD]: Loads scene les.
[SAVE]: Saves scene les.
[USER FILE] Loads user les from an SD memory card or saves them to an SD memory card.
[LOAD]: Loads user les.
[SAVE]: Saves user les.
[SD CARD PROPERTY] Displays the SD memory card status. The format condition, available space, etc. can be checked.
[FORMAT SD CARD] Formats an SD memory card.
[OTHER FUNCTIONS]
Congure these items to make settings for reading/writing, initialization of user le data on the internal memory, and the camera settings.
Item Description of settings
[USER FILE] Loads/saves/initializes user les on the camera memory.
[LOAD]: Loads user les.
[SAVE]: Saves user les.
[INITIALIZE]: Restores user les to the factory settings.
[ACCESS LED] Selects whether to light the access LED of the P2 card.
[ON], [OFF]
f Factory setting: [ON]
[TALLY LAMP] Sets up the tally lamp lighting conditions.
[FRONT]: The front tally lamp lights up.
[REAR]: The rear tally lamp lights up.
[BOTH]: Both the front and rear tally lamps light up.
[OFF]: The tally lamp does not light up.
f Factory setting: [OFF]
[CLOCK SETTING] Sets the built-in calendar (date and time) and time zone.
[TIME ZONE]
For GMT, set using 30 minute intervals from −12:00 to +13:00 (however, +12:45 is possible). After setting
the time, when changing the setting value for [TIME ZONE], the displayed and registered times switch to
the time with the time difference.
[GL PHASE] When in HD (1080i, 720P) mode, selects the output signal of phase to be locked to the signal input to the
<GENLOCK IN/VIDEO OUT> terminal.
[HD SDI]: Locks the HD SDI output signal to genlock input.
[COMPOSITE]: Locks the down-converted composite output signals (signal from the <GENLOCK IN/
VIDEO OUT> terminal and signal of 480i, 576i from the <SDI OUT>terminal) to genlock input.
f Factory setting: [HD SDI]
[H PHASE] Adjusts the horizontal phase when the phase is to be locked to the signal input to the <GENLOCK IN/
VIDEO OUT> terminal.
[−512]…[512]
f Factory setting: [0]
[SEEK POS SEL]
Selects the position to move when the <)>/<%> button is pressed while playback is paused.
[CLIP]: Top of the clip
[CLIP&TEXT MEMO]: Top of the clip and text memo location
f Factory setting: [CLIP]
[GPS] Congures internal GPS settings.
[ON]: Activates the GPS operation. Outputs the location information as a signal to the <SDI OUT> terminal
and records it as clip metadata.
[OFF]: Does not activate the GPS operation. Does not output and record the location information.
f Factory setting: [OFF]
[P.OFF GPS DATA] Retains the GPS location information when the camera is turned off. Sets whether to record the retained
data at the next turning on until a positioning is performed.
[HOLD]: Retains and records data.
[CLEAR]: Clears the data at the time when the camera is turned off. Records 0 (No-Info) at the next
turning on until a positioning is performed.
f Factory setting: [CLEAR]
[MENU INITIALIZE] Restores the whole setting menu including all scene les (1 to 6) and user les to the factory settings.
[MAINTENANCE]
These are items for performing maintenance inspection of the camera. This menu is used for updating the rmware version of the camera.
Item Description of settings
[UPDATE] Performs an update of the camera rmware. (Enabled only when there is a dedicated update le on the SD
memory card.)
[ACTIVATE] This menu activates optional functions (separate fees required).
[DIAGNOSTIC]
This menu is used to display the rmware version, product name, serial number, and operation time of the camera.
To Next Page
Loading...
