Fall S-Curve [0 to 30]
Sets the S-curve for pan/tilt deceleration operation in 31 steps. (The S
becomes stronger, the greater the number)
During the fall acceleration operation for operating at the specified
speed or time during pan/tilt operations by preset playback, the
deceleration process is performed using the S-curve specified in this
setting.
This is enabled only when [Preset Acceleration] is [Manual].
Factory settings: 15
<NOTE>
• In order to limit the deceleration response, in the S-curve step, as
the deceleration speed rises, the limit is automatically applied.
Rise Acceleration [1 to 255]
Sets the acceleration speed for pan/tilt acceleration operation in 255
steps. (The acceleration speed increases as the number increases)
During the acceleration operation for operating at the specified speed
or time during pan/tilt operations by preset playback, the acceleration
process is performed using the acceleration speed specified in this
setting.
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Speed Table].
Factory settings: 128
<NOTE>
• As the speed specified for [Preset Speed] is given priority as the
maximum speed attained in preset playback, if the acceleration
speed specified here is small, this functionality may not operate as
specified.
Fall Acceleration [1 to 255]
Sets the deceleration speed for pan/tilt deceleration operation in 255
steps. (The deceleration speed increases as the number increases)
During the deceleration operation for operating at the specified speed
or time during pan/tilt operations by preset playback, the deceleration
process is performed using the deceleration speed specified in this
setting.
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Speed Table].
Factory settings: 128
<NOTE>
• As the speed specified for [Preset Speed] is given priority as the
maximum speed attained in preset playback, if the deceleration
speed specified here is small, this functionality may not operate as
specified.
Rise Ramp Time [0.1s to 10.0s]
Sets the acceleration time for the time specific operation during preset
playback. (Sets between 0.1 s to 10.0 s in 0.1s increments)
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Time].
Factory settings: 0.1s
<NOTE>
• As the time specified in [Preset Speed] takes precedence as the
total time for preset playback, if the time specified here is more than
half of the time specified in [Preset Speed], this functionality will not
operate as specified.
• When the acceleration operation cannot be performed within the
specified time even at maximum acceleration speed of the device,
the operation will not be performed by the specified time.
Fall Ramp Time [0.1s to 10.0s]
Sets the deceleration time for time specified operations during preset
playback. (Sets between 0.1 s to 10.0 s in 0.1 s increments)
This is enabled only when [Preset Acceleration] is [Manual] and
[Preset Speed Unit] is [Time].
Factory settings: 0.1s
<NOTE>
• As the time specified in [Preset Speed] takes precedence as the
total time for preset playback, if the time specified here is more than
half of the time specified in [Preset Speed], this functionality will not
operate as specified.
• When the deceleration operation cannot be performed within the
specified time even at maximum fall deceleration of the device, the
operation will not be performed by the specified time.
Preset Scope [Mode A, Mode B, Mode C]
Selected here are the setting items to be recalled when the contents
of the preset memory are regenerated.
Mode A
Pan, Tilt, Zoom (including digital zoom), Focus, Iris, Gain,
white balance adjustment value
Mode B Pan, Tilt, Zoom (including digital zoom), Focus, Iris
Mode C Pan, Tilt, Zoom (including digital zoom), Focus
Factory settings: Mode A
Preset Digital Extender [Off, On]
Turns the preset digital extender function off/on.
When set to [On], the digital extender function configuration will be
recalled when regenerating the preset memory.
When set to [Off], the digital extender function configuration will not
be recalled when storing the preset memory.
Factory settings: Off
Preset Thumbnail Update [Off, On]
Turn off/on the function for registering the still image (thumbnail) for
the images being output when a preset memory is registered.
When set to [On], the still image (thumbnail) for the images being
output is registered when registering a preset memory.
When set to [Off], the still image (thumbnail) for the images being
output is not registered when registering a preset memory, but rather
the still image (thumbnail) previously registered is maintained.
Factory settings: On
<NOTE>
• When [IP/HDI|HX] of [OSD Mix] is [On], the character strings
of OSD menu displayed during the generation of still images
(thumbnails) and crop frames are imported to the thumbnails.
• When uploading Camera(ALL), Camera(SYSTEM) or
Camera(PRESET) on the web screen or other access, the still
image (thumbnail) that has been registered in preset memory will be
erased. (→ page 146)
Preset Name [Reset, Hold]
When registering a preset memory, set whether to reset the
previously registered preset name or keep it.
Reset When registering a preset memory, reset the
previously registered preset name.
The preset name after resetting will be [Preset
***
].
(
***
is a 3 digit preset number: 001 to 100)
Hold When registering a preset memory, keep the
previously registered preset name.
Factory settings: Reset
<NOTE>
• The factory default setting for the preset name is [Preset
***
]. (
***
is
a 3 digit preset number: 001 to 100)
• The registration of preset names can be done in the web browser.
0 to 9, A to Z, a to z, _ , and space
120 121
Web screen configurations (continued)
To Next Page
Loading...
