HDMI
Make the settings for output from the HDMI connector.
Format
Set the output format.
The following format settings are possible depending on the [Format]
setting in the [System] screen.
Frequency System Format Format (HDMI)
59.94Hz 2160/59.94p 2160/59.94p
1080/59.94p
2160/29.97p 2160/29.97p
1080/29.97p
1080/59.94p 1080/59.94p
1080/59.94i 1080/59.94i
1080/29.97p 1080/29.97p
1080/29.97PsF 1080/29.97p
1080/23.98p(59.94i)
*
1
1080/23.98p(59.94p)
*
2
720/59.94p 720/59.94p
50Hz 2160/50p 2160/50p
1080/50p
2160/25p 2160/25p
1080/25p
1080/50p 1080/50p
1080/50i 1080/50i
1080/25p 1080/25p
1080/25PsF 1080/25p
720/50p 720/50p
24Hz 2160/24p 2160/24p
1080/24p
1080/24p 1080/24p
23.98Hz 2160/23.98p 2160/23.98p
1080/23.98p
1080/23.98p 1080/23.98p
1080/23.98PsF 1080/23.98p
*
1
It denotes “1080/23.98p over 59.94i”.
*
2
It denotes “1080/23.98p over 59.94p”.
Factory settings:
2160/59.94p (AW-UE80WP/AW-UE80KP)
2160/50p (AW-UE80WE/AW-UE80KE/AW-UE80WED/
AW-UE80KED)
Video Sampling [4:2:2/10bit, 4:2:0/8bit]
When [Format] in [HDMI] is [2160/59.94p] or [2160/50p], select the
video sampling output from the HDMI connector.
4:2:2/10bit Output in 4:2:2/10bit mode.
4:2:0/8bit Output in 4:2:0/8bit mode.
Factory settings: 4:2:2/10bit
<NOTE>
• When [Format] in [HDMI] is other than [2160/59.94p] or [2160/50p],
[Video Sampling] cannot be changed and is fixed at [4:2:2/10bit].
Bar [Camera, Colorbar]
Switch between camera images and color bars.
Camera Camera images
Colorbar Color bar
Factory settings: Camera
Color Bar Type [Type1, Type2]
Select the type of color bar to display.
Type1:
Type2:
This is only enabled when [Bar] is set to [Colorbar].
Factory settings: Type2
Tone [Off, Low, Normal]
Make the settings for the test tone signal (1 kHz) output while the
color bar is displayed.
Off Test tone is not output.
Low Test tone is output at low volume.
Normal Test tone is output at normal volume.
This is only enabled when [Bar] is set to [Colorbar].
Factory settings: Normal
OSD Mix
Selects whether to turn Off/On display of camera menu and status.
3G SDI [Off, On
*
]
Selects whether to turn this Off/On for images output from 3G SDI
OUT connector.
HDMI [Off, On
*
]
Selects whether to turn this Off/On for images output from HDMI
connector.
NDI [Off, On
*
]
Selects whether to turn this Off/On for images of NDI output from the
LAN connector.
IP/NDI|HX [Off, On
*
]
Selects whether to turn this Off/On for images other than NDI images
(H.264/H.265/JPEG/RTMP/SRT/NDI|HX) output from the LAN
connector.
Off The camera menus and statuses are not displayed on the
output pictures covered by the setting items listed above.
On The camera menus and statuses are displayed on the
output pictures covered by the setting items listed above.
*
: Factory settings
<NOTE>
• When this is set to [Off], the camera menu can be displayed for
about 1 minute after the unit is turned on.
OSD Off With R‑Tally [Off, On]
Off or on the function that turns off camera menu, status and other
displays when red tally signals are received via commands or
contacts.
When the red tally signal releases, the camera menu display will
return.
Factory settings: Off
96
Web screen configurations (continued)
To Next Page
Loading...
