VQT2J45
69
Motion pictures encoded in the MPEG2 format, which have
been taken by a Panasonic SD Video Camera, digital video
camera etc, can be stored on HDD or DVD-RAM.
(All the recordings on the same date become a title.)
≥ You cannot playback SD Video on an SD card with this unit.
You must copy the files to the HDD or a DVD-RAM.
≥ You cannot playback or record while copying SD Video.
≥ This unit cannot copy MOTION JPEG format pictures or
AVCHD format pictures from an SD card.
The display below automatically appears when you insert a
card into the SD card slot while stopped.
Press [3, 4] to select “Copy Video ( MPEG2 )”, then press
[OK].
Then go to step 7 on page 66.
≥ SD Video on an SD card are automatically registered on the
copying list.
≥ If there are no SD Video on an SD card, “Copy Video
( MPEG2 )” is not displayed.
Motion pictures encoded in the MPEG2 format, which have
been taken by a Panasonic digital video camera with HDD etc,
can be copied from the camera’s HDD to this unit’s HDD or
DVD-RAM.
(All the recordings on the same date become a title.)
≥ You cannot playback SD Video in the camera’s HDD with this
unit. You must copy the files to the HDD or a DVD-RAM.
≥ You cannot playback or record while copying SD Video.
Tips
To stop copying
Press and hold [RETURN ] for 3 seconds.
(You cannot stop while finalising.)
To return to the previous screen
Press [RETURN ].
Notes
≥ To play DVD-R, DVD-RW (DVD-Video format) and +R on
other players, it is necessary to finalise them after copy.
≥ It is not possible to copy to DVD-R that already contains
JPEG files.
About FR mode
When “Time Setting” is set to “Off” in step 6 (> 68, right
column):
≥ The recording mode is automatically selected by estimating
the remaining capacity of the disc for copying of only the
recorded parts in the video cassette (unrecorded parts will
not be recorded).
≥ When you press [OK] to start copy, the tape is automatically
fast-forwarded to the end and then fast-rewound to the
beginning before the copying is actually started. It may take
time to start copy. If the remaining capacity of the disc is
insufficient, the copying will be stopped in the middle.
≥ The recording is divided into titles every time the tape index
signals are detected.
When “Time Setting” is set to “On” in step 6 (> 68, right
column):
≥ The recording mode is automatically determined by
estimating the remaining capacity of the disc for copying of
the contents equivalent to the recording time set from the
start point of the copying on the video cassette (unrecorded
parts will also be recorded).
≥ The recording is not divided into titles.
Copying Video (MPEG2) from an SD Card
HDD
DVD-RAM
Video (MPEG2)
VIDEO
DVD Video Recording format
SD Card
Copy New Pictures (JPEG)
Copy Video (MPEG2)
View Pictures (JPEG)
SELECT
Start Slideshow
Copy Video ( MPEG2 ) from a video
equipment
Preparation:
1. Turn on both this unit and the camera.
2. Connect the camera to this unit with USB cable.
3. Select the appropriate mode that makes the camera ready
for data transfer (such as “PC CONNECT”) on the camera.
≥ Refer to the camera’s operating instructions for detail.
The display automatically appears when you connect the
camera to this unit. (> 42)
1 Press [3, 4] to select “Video ( DivX & MPEG2 )”, then
press [OK].
2 Press [3, 4] to select “Copy Video ( MPEG2 )”, then
press [OK].
Then go to step 7 on page 66.
≥ SD Video on the camera are automatically registered on the
copy list.
≥ If there are no SD Video on the camera, “Copy Video
( MPEG2 )” is not displayed.
S VIDEO
IN 2
VIDEO
/MONO
AUDIO
RL
DRIVE SELECT
REC
CH
COPYINGCOPYING
VHS
HDD
VHS
DVD
SD CARD
HDD
DVD-RAM
Video (MPEG2)
VIDEO
DVD Video Recording format
USB cable
USB device
Play Video ( DivX )
Copy Video ( MPEG2 )
DMR-EX99VEB_VQT2J45.book 69 ページ ２０１０年１月７日 木曜日 午後１時４１分
To Next Page
Loading...
Need help?
General
