What to do if Panasonic extensions don't operate during a power failure?
During a power failure, if extensions connected to specific ports on MSLC16/CSLC16/SLC16 and DHLC8/SLC8 cards don't work, it could be due to a DPT or APT being connected to the extension port, or an incorrect dialling mode. Disconnect the DPT or APT and connect an SLT. Also, set the Tone/Pulse switch to the other position.
Why is there so much noise on my Panasonic PBX calls?
If you are frequently hearing noise when using your Panasonic PBX, try setting the handset and base unit away from other electrical appliances. Also, move closer to the base unit to improve the signal.
Why do some Panasonic KX-TDA100 PBX extensions not work during a power failure?
To resolve the issue where extensions connected to ports 1 to 4 of MSLC16/SLC16 and ports 1 to 2 of DHLC8/SLC8 cards do not operate during a power failure on your Panasonic PBX, disconnect any DPT or APT devices and connect an SLT instead. Also, ensure the correct dialing mode (tone or pulse) is selected by setting the Tone/Pulse switch to the alternative position.
Why Panasonic Alternate Calling does not function as set?
If Alternate Calling—Ring/Voice and Live Call Screening (LCS) are not functioning as set when using a Panasonic Wireless Phone (KX-T7880/ KX-T7885/KX-TD7894/KX- TD7895), it may be because Voice-calling mode and Hands-free mode with LCS are not available with Wireless Phones. Switch the calling mode to ring-calling or set the LCS mode to "Private".
Why is there noise on Panasonic external paging?
If you're experiencing noise on external paging with your Panasonic system, the issue might be induced noise on the wire between the Hybrid IP-PBX and the amplifier. To resolve this, use a shielded cable for the connection. A short shielded cable is recommended.
What does 'Not Connected' mean on my Panasonic PBX?
If you see 'Not Connected' on your Panasonic PBX, it means the telephone cord between the PBX and the base unit is not connected. Ensure the telephone cord is securely connected.
Why can't I store a long number in my Panasonic KX-TDA100 PBX phonebook?
If you are trying to store a telephone number that is over 24 digits in the last free space in the Phonebook on your Panasonic PBX, try to store the phone number as 24 digits or less, or remove unnecessary data in the Phonebook.
Why can't I register the PS on my Panasonic PBX?
If you are unable to register the PS (Personal Station) on your Panasonic PBX, it could be due to a wrong Personal Identification Number (PIN) registered to the PS, or the CS (Cell Station) is not connected properly. Register the PIN set to the Hybrid IP- PBX into the PS. Make sure that the cable is connected properly with correct pin assignments and that the cable does not make short circuits. Also, switch all DIP switches off.
How to fix Panasonic KX-TDA100 PBX when call transfer doesn't work?
If originating an outside call, call transfer, or conference cannot be performed, it is possible that the corresponding CO button does not exist on the PT. Program the CO button.
What to do if Panasonic PT does not ring?
If your Panasonic PT (Proprietary Telephone) isn't ringing, the ringer volume might be off. Try turning the ringer volume on.
General| System Capacity | Up to 128 extensions |
|---|---|
| VoIP Support | Yes, with optional cards |
| Digital Extensions | Yes |
| Analog Extensions | Yes |
| ISDN Support | Yes |
| Power Supply | AC 100-240 V, 50/60 Hz |
| Operating Temperature | 0°C to 40°C |
| Humidity | 10% to 90% (non-condensing) |
| Networking | Yes |
| Type | Hybrid IP PBX |
| Wireless Capability | Yes |
| Supported Extensions | Digital, Analog |
| Trunk Interfaces | Analog, ISDN |
| Voicemail Capacity | Optional, via voice processing cards |
Guides on initial setup, telephone types, feature numbers, and icon descriptions.
Instructions for initiating various call types, including internal, external, and speed dialing.
Explains how to answer calls, manage call waiting, and receive notifications.
Details call transfer, hold, splitting, conferencing, muting, and monitoring.
Features for call forwarding, absent messages, and extension locking.
Configuration of timed reminders, DND, CLIP/CLIR, BGM, and data security.
Manages call distribution groups, agent status, and queue monitoring.
Call logs, directories, character entry, and system feature access for display phones.
Manager's control over extensions, time modes, and broadcast music.
Customizing PIN, display, call handling, and button assignments.
Manager functions for password changes and extension control.
System-wide configurations like date/time, speed dialing, and extensions.
Solutions for common telephone and system operational problems.
Reference list of features and their corresponding dial codes.
Descriptions and waveforms of audible system tones.
Details changes made in different versions of the user manual.
To Next Page