Why does my Panasonic PS stay out of service after CS is back online?
If the PS (Personal Station) stays out of service after the CS (Cell Station) status changes from Out of Service to In Service on your Panasonic PBX, it may take about 20 seconds for the CS to start up. Wait until the CS starts up.
What causes a Panasonic PBX PS to go out of range?
A Panasonic PBX PS can go out of range due to: * The CSIF card not working. Ensure the CSIF card is properly installed. * The CS not working. Check that the cable is properly connected with correct pin assignments and that there are no short circuits. * The location of the CS not being ideal. * The access system of the PS not being properly set. Change the access system setting of the PS to the appropriate system or automatic.
Why isn't Alternate Calling working on my Panasonic KX-TDA100 PBX with a wireless phone?
If Alternate Calling—Ring/Voice and Live Call Screening (LCS) do not function as set when using a Wireless Phone (KX-T7880/ KX-T7885/KX-TD7894/KX-TD7895) on your Panasonic PBX, it is because Voice-calling mode and Hands-free mode with LCS are not available with Wireless Phones. Switch the calling mode to ring-calling. Set the LCS mode to "Private".
What does '211 Speech path loop-back check error' mean on Panasonic KX-TDA100 PBX?
If you're encountering a '211 Speech path loop-back check error' on your Panasonic PBX, it indicates a potential malfunction with an optional service card (DHLC, DLC, SLC, CSIF, LCOT, T1, PRI, OPB3, IP-GW). Ensure the corresponding optional service card is installed properly. Try pulling out and re-inserting the card. You can also try pressing the Reset Button or replacing the card.
Why is there noise on external paging on my Panasonic PBX?
If you are experiencing noise on external paging with your Panasonic PBX, the issue might be induced noise on the wire between the PBX and the amplifier. To resolve this, use a shielded cable for the connection. A short shielded cable is recommended.
Why alternate calling ring/voice and live call screening do not function when using a wireless phone on my Panasonic KX-TDA100?
To resolve issues with Alternate Calling—Ring/Voice and Live Call Screening (LCS) when using a Wireless Phone (KX-T7880/ KX-T7885/KX-TD7894/KX- TD7895) on your Panasonic PBX: * Switch the calling mode to ring-calling. * Set the LCS mode to "Private". Voice-calling mode and Hands-free mode with LCS are not available with Wireless Phones.
Why can't I register my Panasonic PBX PS?
If you're having trouble registering your Panasonic PBX PS, consider these potential causes: * The Personal Identification Number (PIN) registered to the PS might be incorrect. Ensure you enter the PIN set in the PBX into the PS. * The CS might not be connected properly. Verify that the cable is correctly connected with the correct pin assignments and that there are no short circuits. * The CS might not be set for normal operation. Try switching all DIP switches off.
Why is there frequent noise when using the Panasonic KX-TDA100 PS?
Noise during PS use may be due to call handover issues.
How to fix noise on external paging with Panasonic KX-TDA100?
To resolve noise on external paging, use a shielded cable as the connection wire between the PBX and the amplifier. A short shielded cable is recommended.
What causes distorted external music on a Panasonic PBX?
Distorted external music is caused by an excessive input level from the external music source. Decrease the output level of the external music source using the volume control on the music source.
General| System Capacity | Up to 128 extensions |
|---|---|
| VoIP Support | Yes, with optional cards |
| Digital Extensions | Yes |
| Analog Extensions | Yes |
| ISDN Support | Yes |
| Power Supply | AC 100-240 V, 50/60 Hz |
| Operating Temperature | 0°C to 40°C |
| Humidity | 10% to 90% (non-condensing) |
| Networking | Yes |
| Type | Hybrid IP PBX |
| Wireless Capability | Yes |
| Supported Extensions | Digital, Analog |
| Trunk Interfaces | Analog, ISDN |
| Voicemail Capacity | Optional, via voice processing cards |
Guides on initial setup, telephone types, feature numbers, and icon descriptions.
Instructions for initiating various call types, including internal, external, and speed dialing.
Explains how to answer calls, manage call waiting, and receive notifications.
Details call transfer, hold, splitting, conferencing, muting, and monitoring.
Features for call forwarding, absent messages, and extension locking.
Configuration of timed reminders, DND, CLIP/CLIR, BGM, and data security.
Manages call distribution groups, agent status, and queue monitoring.
Call logs, directories, character entry, and system feature access for display phones.
Manager's control over extensions, time modes, and broadcast music.
Customizing PIN, display, call handling, and button assignments.
Manager functions for password changes and extension control.
System-wide configurations like date/time, speed dialing, and extensions.
Solutions for common telephone and system operational problems.
Reference list of features and their corresponding dial codes.
Descriptions and waveforms of audible system tones.
Details changes made in different versions of the user manual.
To Next Page