Panasonic Omnivision PV-7451 - VCR Plus+ Channel Setup; Channel Setup Preparations

In order for the VCR to read the VCR Plus+ code, some set up is required. A Guide (VCR Plus+) channel number is assigned to
each local broadcast and cable station. Because this number sometimes differs from the channel your TV receives the station
on, it is necessary to program the VCR with local channel information.
r __ VCR Plus+ Channel Setup
j |1 For Connection Type B (page 24) only
“ ^lll * Before you begin, complete the Channel Setup
(0 1 0 0 011 11 Preparations below left.
^_^ II ^ Important Note:
// \\ - (S) (IS) If your VCR connection type changes from type A to B, repeat
/ /f• steps 1-4 of page 24 and select VCR^CABLE/DSS BOXkTV
1 / ®) (@) or before proceeding with these steps.
fiT) (§)_I /TTN/ph - Push MENU to . m enu.
^ X o HfSl VSU r\ display the menu. setups
OBJLfl
)
£ BE
O © viT
© © ©
© © ©
© © 0 -
i® ft fti
SET UP VCR
SET CLOCK
ADD/
DELETE
o U
s°ss
Channel Setup Preparations
NOTE: Complete the steps on this page if your
VCR hook-up resembles “B” on page 24.
Prepare a list like the example below.
This list will help you smoothly enter the
information needed in step “d" at right.
You will need the following to complete the list;
■ A line up of normal and/or cable stations you
receive along with the channel numbers your
TV receives them on. A cable channel line-up
chart is supplied by your cable company.
■ A list of Guide (VCR Plus+) channel numbers
assigned to the stations you receive. This list is
available in TV Guide and the TV listings found
in selected newspapers.
■ I Make a chart with 3 columns like the example
1 below. In the left column, fill in the name or call
letters of the stations you receive.
O In the middle column, fill in each station’s
assigned Guide (VCR Plus+) number found in
TV Guide, newspapers, etc.
O In the right column, fill in the channel number
u that your TV receives the station on from your
channel line-up.
EXAMPLE ONLY
Broadcast or Cable
Station Name
HBO
Nickelodeon
CBS
FOX
Assigned
Channel no.
Guide
your TV
(VCR Plus+)
receives the
channel no.
station on
33
15
38 20
04
04
11
tDIOMA/LANGUE:ENGLISH
SELECT :* t key
SET : ► KEY
END :MENU KEY
a'"I Push AW to select l 8 ” :MENU «
“SET UP CHANNEL,”
■ S'' 1 and then push ► to display
• the “SET UP CHANNEL” screen.
Voy
Push AT to select
“VCR Plus+ CH SET
UP,” and then push ►
to display the “VCR
Plus+ CH SET UP”
screen.
--- SET UP CHANNEL ---
ANTENNA SYSTEM : CATV •
AUTO SET
CABLE/DSS BOX SET UP
SELECT:* ▼ KEY
SET : ► KEY
END :MENU KEY
IMPORTANT NOTE:
For step “d,” use the list you prepared. You may leave lines
blank if you don’t receive that station, or if the GUIDE CH
number and the CATV (or TV) CH numbers are the same.
^ t0 m0ve
; the shaded area to
! the right side.
Then, push AT to change CATV
or TV CH number.
Next, push M to set the number.
Now, push AT to continue.
Repeat this operation until the list is
complete.
VCR PIu s + CH SET UP
SELECT:* ▼ KEY
SET : ► KEY
END :MENU KEY
VCR Plus* CH SET UP
GUIOE CH CATV CH
SELECT:* ▼ KEY
SET : ■ * KEY
END :MENU KEY
To Make Corrections
Push AT and ► to select the incorrect CATV or TV CH number.
Then, push AT to change, or ADD/DLT to delete the channel.
Push MENU three times
to exit the VCR Plus+ CH
SET UP mode.
Make each entry within 5 minutes or the VCR will leave this mode.
Once local channels have been programmed, they will stay in
memory, even in the case of a power failure.
VCR Plus+ and PlusCode are trademarks of Gemstar
Development Corporation. The VCR Plus+ system is manufactured
under license from Gemstar Development Corporation.
More
You
Can
Do