Panasonic PT-MZ780

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 113
10) Press
as
to select a [COMMAND].
f
For [COMMAND] which requires detailed settings, the items of the detailed settings will switch each time
you press
qw
.
f
When [INPUT] is selected, press the <ENTER> button, and then press
asqw
to select the input to be
set.
[COMMAND]
Detailed settings of
[COMMAND]
Description
[POWER ON]
― Switches on the projector.
[STANDBY]
― Enters standby.
[QUICK STARTUP]
[ON]
Enables the function of the [PROJECTOR SETUP] menu
→
[ECO
MANAGEMENT]
→
[QUICK STARTUP].
[OFF]
Disables the function of the [PROJECTOR SETUP] menu
→
[ECO
MANAGEMENT]
→
[QUICK STARTUP].
[SHUTTER]
[OPEN]
Disables the shutter function (shutter: open).
[CLOSE]
Enables the shutter function (shutter: closed).
[INPUT]
[COMPUTER]
Switches the input to COMPUTER.
[HDMI1]
Switches the input to HDMI1.
[HDMI2]
Switches the input to HDMI2.
[HDMI3]
Switches the input to HDMI3.
[DIGITAL LINK]
Switches the input to DIGITAL LINK.
[INPUT1] - [INPUT10]
*1
Switches the input to DIGITAL LINK, and switches the input of the
Panasonic twisted-pair-cable transmitter to the specied input.
[LIGHT POWER]
[NORMAL]
Prioritizes luminance.
[ECO]
Controls the power to increase the life of the light source although
the luminance is lower than that of [NORMAL].
[QUIET]
Prioritizes the operation with less noise although the luminance is
lower than that of [NORMAL].
[USER]
Controls the power according to settings in [USER].
[IN STANDBY MODE(AUDIO)]
[OFF]
Stops the audio output during standby.
[ON]
Outputs the audio during standby.
[VOLUME] [0] - [63]
Sets the volume.
*1 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reected from [INPUT1] to [INPUT10]. When an item that does not reect the input name is selected, it will be disabled.
11) Press the <ENTER> button.
f
The command is xed and
n
is displayed at the left of the selected command.
f
After the command is xed, press the <MENU> button to close the detailed setting screen.
12) Press
asqw
to select [STORE], and press the <ENTER> button.
Note
f
To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step
5)
is
displayed, or select [DELETE] at the screen in Step
6)
and press the <ENTER> button.
f
If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f
The operating time will be the local time. (
x
page 111)
f
If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
[MULTI PROJECTOR SYNC]
Set the contrast synchronization function and the shutter synchronization function.
The contrast synchronization function is a function to display a combined screen with a balanced contrast by
sharing the brightness level of the video signal input to each projector when a multi-display is constructed
by combining the projected image of multiple projectors. The shutter synchronization function is a function to
synchronize the shutter operation of the specied projector to other projectors, and the effect using the shutter
function including the fade out/fade in operation can be synchronized.