Panasonic SC-ALL70T User Manual

Getting started
SQT0935
21
10 Press [OK] on the remote control to
exit the setting.
≥ Your compatible device automatically connects to
the original network.

≥ Enable Java and cookies in your browser settings.
≥ Wireless connection setting cancels after 20 minutes
elapse.
≥ Do not connect a LAN cable. Doing so will
disable the Wi-Fi function.
≥ The following explanations are based on a
smartphone.
1 Turn this system on.
2 To enter “WPS PUSH” mode
1 Press [SETUP] on the remote control
repeatedly to select “NET SETUP”.
2 Press [ 4 ][ 3 ] on the remote control to
select “WPS PUSH” and then press [OK].
3 Press [4][3] on the remote control to
select “YES” and then press [OK].
≥ Alternatively, touch and hold [INPUT] and
[ -PAIRING] on the main unit for at least 4
seconds.
≥ Proceed to the next step after the display on the
main unit changes from a flashing “WAIT” display to
a flashing “WPS” display.
3 Activate the WPS button on the
wireless router.
≥ On the main unit’s display, “SUCCESS” appears
when the connection is established. (“ ” will be
displayed.)
– “FAIL” may be displayed if the connection was not
made within the set time limit. Try the setting
again. If “FAIL” is still displayed, try other
methods.
4 Press [OK] on the remote control to
exit the setting.
∫ Using the WPS PIN code
1 Turn this system on.
2 Press [SETUP] on the remote control
repeatedly to select “NET SETUP”.
3Press [4][3] on the remote control to
select “WPS PIN” and then press [OK].
≥ Proceed to the next step after the display on the
main unit changes from a flashing “WAIT” display to
a “64428147” display.
4 Enter the PIN code “64428147” into the
wireless router.
≥ On the main unit’s display, “SUCCESS” appears
when the connection is established. (“ ” will be
displayed.)
– “FAIL” may be displayed if the connection was not
made within the set time limit. Try the setting
again. If “FAIL” is still displayed, try other
methods.
5 Press [OK] on the remote control to exit
the setting.

≥ Depending on a router, other connected devices may
temporarily lose their connection.
≥ For details, refer to the operating instructions of the
wireless router.
≥ Wireless connection setting cancels after 2 minutes
elapse.
Method 2:
Using WPS
(Wi-Fi Protected Setup
TM
)
A compatible
wireless router
may have the
WPS identifier
mark.
e.g.,
SC-ALL70T-SQT0935.book 21 ページ ２０１５年４月２８日 火曜日 午前１０時５分

Panasonic SC-ALL70T Specifications

General

Audio decoders	Dolby Digital, Dolby Pro Logic II, DTS Digital Surround
RMS rated power	350 W
Audio output channels	3.1 channels
Audio Return Channel (ARC)	Yes
Impedance	6 Ω
Woofer diameter	160 mm
Soundbar speaker RMS power	70 W
Total Harmonic Distortion (THD)	10 %
Subwoofer connectivity	Wireless
Receiver included	-
Product color	Black
HDMI in	1
Connectivity technology	Wired & Wireless
AC input voltage	220-240 V
AC input frequency	50 Hz
Power consumption (standby)	0.48 W
Power consumption (typical)	42 W

Weight and Dimensions

Depth	120 mm
Width	950 mm
Height	55 mm
Soundbar weight	2600 g
Subwoofer depth	303 mm
Subwoofer width	180 mm
Subwoofer height	378 mm
Subwoofer weight	5000 g