Panasonic SC-BT222

Reference
37
VQT2S28
The images from this unit do not appear on the TV.
Picture is distorted.
Jittering occurs.
≥ An incorrect resolution is selected in “HDMI Video Format”.
Reset the setting as follows:
While the disc tray is empty and “BD/DVD” is selected as a
source, press and hold [1] (Play) and [∫] (Stop) on the main
unit at the same time for more than 5 seconds to cancel the
setting.
≥ When Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio
are not output in bitstream, select “Yes” in “Default Settings”
and make proper settings. (> 34)
≥ The unit and television are using different video systems.
While stopped, keep pressing [∫] (Stop) and [< OPEN/
CLOSE] on the main unit for 5 or more seconds. The system
switches from PAL to
NTSC or vice versa.
≥ The system used on the disc doesn’t match your television.
– PAL discs cannot be correctly viewed on an NTSC
television.
– This unit can convert NTSC signals to PAL60 for viewing
on a PAL television (“NTSC Contents Output” in the
“Picture”).
Video is not output.
≥ Set the “High Clarity Sound” in the playback menu to “Off” to
use the VIDEO OUT terminal. (> 30)
Video is not output in high definition.
≥ Confirm that “HDMI Video Format” in the Setup menu is set
properly. (> 33)
A black band is displayed around the edge of the screen.
The aspect ratio of the screen is abnormal.
≥ Confirm the “TV Aspect” is set properly. (> 33)
≥ Adjust the aspect setting on the television.
(Adjustment using “Screen Aspect” (> 21) on the unit is also
possible.)
After choosing “Home Cinema” in “Speaker Selection” with
the TV’s remote control, the TV’s input selection also changes.
≥ Disconnect the HDMI cable from the TV and reconnect it to a
different HDMI IN terminal.
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio type.
≥ Check connections to speakers and other equipment.
(> 12s16)
≥
To output audio from a device connected with an HDMI cable,
set “HDMI Audio Output” to “On” in the Setup menu. (
> 34)
≥ When “BD-Video Secondary Audio” is set to “On”, Dolby
TrueHD, Dolby Digital Plus, DTS-HD Master Audio and
DTS-HD High Resolution Audio are output as Dolby Digital
or DTS Digital Surround.
≥ Re-master will not work when the bitstream signal is output
from the HDMI AV OUT terminal. (> 30)
≥ Depending on the connected equipment, the sound may be
distorted if this unit is connected with an HDMI cable.
No surround sound.
≥ Press [SURROUND] to select a surround effect. (> 19)
Cannot switch audio.
≥ When audio is output from the HDMI AV OUT terminal, set
“Dolby D/Dolby D +/Dolby TrueHD”, “DTS/DTS-HD” or
“MPEG Audio” to “PCM”. (> 32)
No sound from the TV.
≥ Press [EXT-IN] to select the corresponding source. (> 18)
≥ The ARC (Audio Return Channel) function is not available.
Instead, use an optical digital audio cable or an audio cable
to have the TV sound. (> 14, 15)
≥
If the TV is not ARC compatible and only the HDMI connection
is used, an extra audio connection is necessary (
> 14, 15).
TV screen and video Sound
SCBT222EBEG_VQT2S28-B.book 37 ページ ２０１０年２月１２日 金曜日 午後１時４分