7
FM/AM radio
Manual tuning
1 Press [ FM/AM] to select “FM” or “AM”.
2 Press [ TUNE MODE] to select “MANUAL”.
3 Press [ 2/3] or [5/6] to select the
frequency of the required station.
To tune automatically
Press and hold [2/3] or [5/6] until the
frequency starts changing rapidly.
• Auto tuning may be interrupted when there is excessive
interference.
• To cancel auto tuning, press [2/3] or [5/6]
once again.
To improve the sound quality
When “FM” is selected
Press [ FM MODE] to display “MONO”.
Press again to cancel.
• “MONO” is also cancelled if the frequency is changed.
• Turn off “MONO” for normal listening.
When “AM” is selected
Press and hold [ TUNE MODE].
Each time you press and hold the button: BP 2
BP 1
RDS broadcasting
This unit can display the text data transmitted by the
radio data system (RDS) available in some areas.
Press [ DISPLAY] to display:
RDS displays may not be available if reception is poor.
Station name
(PS)
]
Program type
(PTY)
]
Frequency
(FREQ)
Memory preset
30 FM and 15 AM stations can be preset.
Automatic presetting
1 Press [PLAY MODE] to select “CURRENT” or
“LOWEST” frequency.
2 Press [ AUTO PRESET] to start presetting.
Manual presetting
1 Press [TUNE MODE] to select “MANUAL”.
2
Press
[2/3] or [5/6]
to tune to the
required station.
3 Press [ PROGRAM].
4 Press the numeric buttons to select a channel.
The station occupying a channel is erased if another
station is preset to that channel.
5 Repeat steps 2 to 4 to preset more stations.
Selecting a preset station
1 Press [TUNE MODE] to select “PRESET”.
2 Press
[2/3] or [5/6] to select the
channel.
Alternatively, press the numeric buttons to select the
channel.
AM allocation setting
(by main unit only)
This system can also receive AM broadcasts allocated in
10 kHz steps.
Press and hold [FM/AM].
After a few seconds the display changes to a fl ashing
display of the current minimum frequency. Release the
button when the minimum frequency changes.
• To return to the original step, repeat the above steps.
• After changing the setting, previously preset frequency
will be cleared.
USB
The USB connectivity enables you to connect and play
MP3 tracks from USB mass storage device.
Preparation
Before connecting any USB mass storage device to the
unit, ensure that the data stored therein has been backed
up.
Do not use a USB extension cable. The USB mass
storage device connected via the cable will not be
recognised by this unit.
1 Reduce the volume and connect the USB mass
storage device to the USB port.
Hold the main unit when connecting or disconnecting
the USB mass storage device.
2 Press [ 4/9, USB] to start play.
Stop
playback
Press [ 8]. “RESUME” is displayed.
The position is memorised.
Press [4/9, USB] to resume play.
Press [8 ] again to clear the position.
For other operations, they are similar as those
described in “Discs” (Z page 6).
Compatible devices
Devices which are defi ned as USB mass storage class:
• USB devices that support bulk only transfer.
• USB devices that support USB 2.0 full speed.
Supported formats
• Track must have the extension “.mp3” or “.MP3”.
• CBI (Control/Bulk/Interrupt) is not supported.
• A device using NTFS fi le system is not supported.
[Only FAT 12/16/32 (File Allocation Table 12/16/32) fi le
system is supported.]
• Depending on the sector size, some fi les may not work.
• Maximum album: 255 albums
• Maximum track: 2500 tracks
• Maximum track in one album: 999 tracks
7
SC-PM04_RQT9699-E_EC.indb 7SC-PM04_RQT9699-E_EC.indb 7 4/23/2012 5:28:04 PM4/23/2012 5:28:04 PM
To Next Page
Loading...
Need help?
General
Weight and Dimensions
