Press [SOUND] to select a sound mode.
Every time you press [SOUND] on the remote control:
Preset EQ
Press [SOUND] to select “EQ” and press [q] to make selection:
HEAVY : Adds punch to rock.
CLEAR : Clarifies higher sounds.
SOFT : For background music.
EQ-OFF : Canceled (no effect is added).
Manual EQ
Create your own sound quality effects.
1 Press [SOUND] to select “M.EQ”.
2 Change the sound quality with the cursor buttons.
Select the sound range to be adjusted with [w] or [q].
(Within 7 seconds or so)
Adjust the level with [u, 2/REW] or [i, 1/FF].
(–3 to +3)
Repeat step 2 to set the desired sound quality.
The original display is restored on the display panel in about 3
seconds.
The changes you make are stored and automatically
recalled the next time you select “M.EQ”.
Enhancing the bass
You can enhance low-frequency sound so that heavy bass
sound can be heard clearly, even if the acoustics of your room
are not optimal. The unit automatically selects the most suitable
setting according to the type of playback source.
Press [SOUND] to select “H.BASS” and press [q] to make
selection: H. BASS ON H. BASS OFF
Pressing [H.BASS] on the main unit will also makes the
“H.BASS”: H. BASS ON H. BASS OFF
Sound field and sound quality
31
The following sound effects may not be available or have no effect depending on the type of source, or when microphone(s) or
headphones are inserted, or karaoke function is on or play speed is on.
You may experience a reduction in sound quality when these sound field systems are used with some sources. If this occurs, turn
the sound field system off.
•
•
Surround
Sound field and sound quality
Changing the sound quality
M.EQ H.BASSEQ
SUBW LVL
MIDBASS TREBLE
On the main unit
1 Press [MANUAL EQ].
“BASS” is selected and adjusted by turning
[– BASS CONTROL +].
2 Adjust the level for “MID” and “TREBLE” with
[2/REW/u] or [1/FF/i].
MID TREBLE
ECHO C. FOCUS
CH SEL.
Press [SURROUND] to select a surround mode.
Every time you press [SURROUND] on the remote control:
STANDARD : Sound is output as it was recorded/encoded.
Speaker output varies depending on the
source.
MULTI-CH : You can enjoy sound from the front
speakers, as well as the surround speakers
even when playing a 2-channel sound or
non-surround sound.
MANUAL
: ( below)
Selecting other surround modes
While “MANUAL” is displayed, press [w, q] to make selection:
PLII MOVIE
1
: Suitable for movie, or the one recorded in
Dolby Surround. (except )
PLII MUSIC
1
: Adds 5.1-channel effects to stereo
sources. (except )
S.SRND
MUSIC
3
: Adds surround effects to stereo sources.
S.SRND
MOVIE
3
: Use this mode when playing movie.
S.SRND
PARTY
3
: Sound is in stereo regardless of the
direction you are facing.
SURROUND
ENHANCER
2
: Automatically adjusts each speaker to
enhance the surround sound effect of
5.1-channel audio. When playing two-
channel audio, the audio of the L/R front
speakers is also output through the rest of
the speakers creating a surround sound
effect.
STEREO : Sound will be output to the front speakers
and the subwoofer only for any sources.
1
“ %PLII ” lights up if there is effects.
2
“ENH” lights up if there is effects.
3
“ ” lights up if there is effects.
Dolby PLII Movie and Dolby PLII Music will only have effects
during DVD/CD and USB playback.
S.SRND does not work when playing sources with multi
channel.
When S.SRND is on, Dolby PLII and Surround Enhancer are
turned off.
•
•
•
MANUALSTANDARD
MULTI-CH
Note
DivX
DivX
On the main unit
Pressing [SURROUND ENHANCER] will enable you
to choose between “STANDARD” and “SURROUND
ENHANCER”.
To Next Page
Loading...
