Panasonic WV-SFN130 - User Manual

Other manuals for Panasonic WV-SFN130

Questions and Answers:

D
darlenegoodmanAug 18, 2025
What to do if Panasonic Security Camera images cannot be saved on the SD memory card?
- R
  Richard JohnsonAug 18, 2025
  If you cannot save images to the SD memory card or encounter write/read errors with your Panasonic Security Camera, first verify that the SD memory card is correctly inserted. Ensure that the write protect switch is not set to “LOCK”. If “********MB/ ********MB” is displayed under “Remaining capacity” on the [SD memory card] tab, this indicates the card is write-protected. If “--------MB/--------MB” is displayed on “Remaining capacity”, format the SD memory card. Also, format the SD memory card if any recognition error is received when the “Diag.” of “E-mail notification” or “Panasonic alarm protocol” is used. If “########MB/########MB” is displayed on “Remaining capacity”, check the password lock configuration.
S
Sarah WilsonAug 21, 2025
Why is there no audio output from my Panasonic WV-SFN130?
- W
  Willie JacksonAug 21, 2025
  If you are not getting audio output from your Panasonic Security Camera on devices like a network disk recorder or PC software, the issue might be due to codec incompatibility. Some devices may not support “G.711”, "AAC-LC" or “AAC-LC (HIGH QUALITY)”. To resolve this, set the audio encoding format of the camera to “G. 726 (32 kbps).”
L
Luke RobinsonAug 25, 2025
Why does Panasonic Security Camera authentication window is displayed repeatedly?
- H
  heathermyersAug 25, 2025
  If you repeatedly see an authentication window when trying to access your Panasonic Security Camera, and you've changed the [Authentication] setting, close your web browser and try accessing the camera again. Also consider if the username or password was changed.
S
Samuel SalinasAug 28, 2025
How to fix Panasonic WV-SFN130 Security Camera images are displayed blurry?
- A
  Audrey BurgessAug 28, 2025
  To resolve blurry images on your Panasonic Security Camera, make sure that the focus is adjusted correctly.
D
Daniel JonesSep 1, 2025
What to do if cannot access Panasonic Security Camera via the URL of the “Viewnetcam.com” service?
- J
  James BushSep 1, 2025
  To resolve issues accessing your Panasonic Security Camera via the URL of the “Viewnetcam.com” service, log into the “My Account” page of “Viewnetcam.com” website (http://www.viewnetcam.com/) to check the information of the registered camera. If the global address is not displayed for the IP address, access the camera, and register the user information for the “Viewnetcam.com” service on the [Advanced] tab on the “Network” page of the setup menu.
J
Jeremiah GrahamSep 4, 2025
What to do if SD CARD indicator lights up red on Panasonic WV-SFN130?
- J
  jnielsenSep 4, 2025
  If the SD CARD indicator lights up red on your Panasonic Security Camera, it could be due to several reasons: * The write protect switch on the SD card might be set to “LOCK”. In this case, unlock the write protect switch. * The SD card may have been formatted on a PC. If so, use an SD memory card formatted on the camera itself. * The SD card might be faulty. Try replacing it with a normal one.
E
esimmonsSep 7, 2025
How to fix a Panasonic WV-SFN130 when the power is not turned on?
- D
  David OwensSep 7, 2025
  If your Panasonic Security Camera is not turning on, ensure that the PoE device and the network connector are connected using an Ethernet cable of category 5e or better, and verify the connection is properly established. Also, the power supply might stop if the demanded power exceeds the total power limit for all PoE ports. Refer to the operating instructions of your PoE device.
D
dylanlawrenceSep 10, 2025
Why doesn't the LINK indicator light up on my Panasonic WV-SFN130?
- E
  erin54Sep 12, 2025
  If the LINK indicator on your Panasonic Security Camera does not light up orange when the Ethernet cable is connected, check the following: 1. Ensure the Ethernet cable is properly connected. 2. Verify that the hub or router connected to the camera is operating correctly. 3. Replace the Ethernet cable to exclude the possibility of a broken cable.

Panasonic WV-SFN130 Specifications

General

Camera Type	Network Camera
Image Sensor	1/3" MOS sensor
Resolution	1280 x 960
Focal Length	3.6 mm
Day/Night Function	Yes
IR Cut Filter	Yes
Network Interface	10Base-T / 100Base-TX
Ethernet	Yes
Wireless	No
Ingress Protection	IP66
Lens Mount	Fixed
Signal-to-Noise Ratio	More than 50 dB
Effective Pixels	Approx. 1.3 million pixels
Lens	Fixed
Video Compression	H.264, JPEG
Audio Compression	G.711
Audio Input/Output	1 input, 1 output
Power Supply	DC 12V, PoE (IEEE 802.3af)
Power Source	DC 12 V
Operating Temperature	-10°C to +50°C (14°F to 122°F)
Angle of View	H: 89°, V: 67°, D: 107°