“JPEG(1)”, “JPEG(2)”, and “JPEG(3)” can only be selected for the “Recording format” of “Recording stream
1”.
• Off: Does not record data.
• JPEG(1): Records still image data (JPEG(1)). The data is recorded in accordance with the settings of
“JPEG(1)” on the [JPEG/H.264] tab of the “Image/Audio” page.
• JPEG(2): Records still image data (JPEG(2)). The data is recorded in accordance with the settings of
“JPEG(2)” on the [JPEG/H.264] tab of the “Image/Audio” page.
• JPEG(3): Records still image data (JPEG(3)). The data is recorded in accordance with the settings of
“JPEG(3)” on the [JPEG/H.264] tab of the “Image/Audio” page.
• H.264(1): Records video data (H.264(1)) in the MP4 video encoding format. The data is recorded in
accordance with the settings of “H.264(1)” on the [JPEG/H.264] tab of the “Image/Audio” page.
• H.264(2): Records video data (H.264(2)) in the MP4 video encoding format. The data is recorded in
accordance with the settings of “H.264(2)” on the [JPEG/H.264] tab of the “Image/Audio” page.
• H.264(3): Records video data (H.264(3)) in the MP4 video encoding format. The data is recorded in
accordance with the settings of “H.264(3)” on the [JPEG/H.264] tab of the “Image/Audio” page.
• H.264(4): Records video data (H.264(4)) in the MP4 video encoding format. The data is recorded in
accordance with the settings of “H.264(4)” on the [JPEG/H.264] tab of the “Image/Audio” page.
• Default:
– Recording stream 1: JPEG(2)
– Recording stream 2: Off
IMPORTANT
• If an SD memory card with an SD Speed Class other than 10 is used, set the maximum combined bit
rate of "H.264(1)", "H.264(2)", "H.264(3)", and "H.264(4)" selected in "Recording format" to the
following. (up to 6 Mbps)
• If an SD memory card with an SD Speed Class 10 is used, set the maximum combined bit rate of “H.
264(1)”, “H.264(2)”, “H.264(3)”, and “H.264(4)” selected in “Recording format” to the following. (up to
16 Mbps)
• If an SD memory card with an SD Speed Class 10 is used, use the card with UHS-I (Ultra High
Speed-I).
Note
• When “H.264(1)” is selected, the settings for “H.264(1)” on the [JPEG/H.264] tab of the “Image/
Audio” page will be changed to the settings for “H.264(1) & recording”.
When “H.264(2)” is selected, the settings for “H.264(2)” on the [JPEG/H.264] tab of the “Image/
Audio” page will be changed to the settings for “H.264(2) & recording”.
When “H.264(3)” is selected, the settings for “H.264(3)” on the [JPEG/H.264] tab of the “Image/
Audio” page will be changed to the settings for “H.264(3) & recording”.
When “H.264(4)” is selected, the settings for “H.264(4)” on the [JPEG/H.264] tab of the “Image/
Audio” page will be changed to the settings for “H.264(4) & recording”.
• When using the SD memory recording function of a Panasonic network disk recorder, select
“JPEG(1)” for “Recording format” of “Recording stream 1”.
• When “H.264(1)”, “H.264(2)”, “H.264(3)”, or “H.264(4)” is selected for “Recording format”, the settings
of the following functions may be corrected.
– When “Best effort” is selected for “Transmission priority”, “Frame rate” is set.
– When “High” or “Middle” is selected for “Burst tolerance level”, “Low” is set.
– When “2s”, “3s”, “4s” or “5s” is selected for “Refresh interval”, “1s” is set.
• When “H.264(1)”, “H.264(2)”, “H.264(3)”, or “H.264(4)” is selected for “Recording format”, the name of
the saved file will be given automatically.
• When “H.264(1)”, “H.264(2)”, “H.264(3)”, or “H.264(4)” is selected for “Recording format”, the number
of users that can access the camera may be reduced.
54 Operating Instructions
10 Configure the basic settings of the camera [Basic]
To Next Page
Loading...
