Parker F11 series - Page 16

Bulletin MSG30-5511-M1/UK
16
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Service Manual/Spare Parts
Series F11
Assemble F11
21. Carefully tap down shaft seal and sup-
port ring.
22. Assemble the retaining ring. Make sure
the chamfer is downwards.
23. Assemble the hex. screws and torque
them to specified value, shown on
page 17.
24. Tap down the flat key and turn the
shaft at least one rev. Make sure the
back-lash of the gears are correct
(see page 17).
Bulletin MSG30-5511-M1/UK
Series F11
16
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Service Manual/Spare Parts
Assembly F11
Assembling
3. Placethedistanceringonthebig
taperedrollerbearing.
6. Placethelockwasher(s)ontothe
shaft.
21. Carefullytapdownshaft seal
and supportring.
22. Assembletheretainingring. Make
surethechamferis downwards.
retaining
ring
back-upring
23. Assemblethehex.screws and
torquethemtospecified value,
shownonpage17.
24. Tapdowntheflatkeyand turnthe
shaftatleastonerev. Make surethe
back-lashofthe gearsare correct(see
page17).
Assembling
Bulletin MSG30-5511-M1/UK
Series F11
16
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Service Manual/Spare Parts
Assembly F11
Assembling
3. Placethedistanceringonthebig
taperedrollerbearing.
6. Placethelockwasher(s)ontothe
shaft.
21. Carefullytapdownshaft seal
and supportring.
22. Assembletheretainingring. Make
surethechamferis downwards.
retaining
ring
back-upring
23. Assemblethehex.screws and
torquethemtospecified value,
shownonpage17.
24. Tapdowntheflatkeyand turnthe
shaftatleastonerev. Make surethe
back-lashofthe gearsare correct(see
page17).
Bulletin MSG30-5511-M1/UK
Series F11
16
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Service Manual/Spare Parts
Assembly F11
Assembling
3. Placethedistanceringonthebig
taperedrollerbearing.
6. Placethelockwasher(s)ontothe
shaft.
21. Carefullytapdownshaft seal
and supportring.
22. Assembletheretainingring. Make
surethechamferis downwards.
retaining
ring
back-upring
23. Assemblethehex.screws and
torquethemtospecified value,
shownonpage17.
24. Tapdowntheflatkeyand turnthe
shaftatleastonerev. Make surethe
back-lashofthe gearsare correct(see
page17).
Bulletin MSG30-5511-M1/UK
Series F11
16
Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Service Manual/Spare Parts
Assembly F11
Assembling
3. Placethedistanceringonthebig
taperedrollerbearing.
6. Placethelockwasher(s)ontothe
shaft.
21. Carefullytapdownshaft seal
and supportring.
22. Assembletheretainingring. Make
surethechamferis downwards.
retaining
ring
back-upring
23. Assemblethehex.screws and
torquethemtospecified value,
shownonpage17.
24. Tapdowntheflatkeyand turnthe
shaftatleastonerev. Make surethe
back-lashofthe gearsare correct(see
page17).