EasyManua.ls Logo

PARMA-TECHNIK MIKRON III A - User Manual

Default Icon
32 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
','
PARMA-TECHNIK, s.r.o.
Uherskobrodska 962
763
26
Luhacovice
CZECH REPUBLIC
AEROTECHNIK
Tel: + 420 577
131
210
~s.r.o.
Fax:+
420577131210
e-mail: info@parmatechnik.cz
OPERATING AND MAINTENANCE MANUAL
MIKRON III A
II
AIRCRAFT ENGINE AND ITS VERSIONS
Document No.: 610902
Issue: 5/92
Question and Answer IconNeed help?

Do you have a question about the PARMA-TECHNIK MIKRON III A and is the answer not in the manual?

Summary

1. General

1.1 Content, List of Effective Pages

Lists the content and effective pages of the manual.

1.2 List of Revisions and Amendments

Provides a list of revisions and amendments made to the manual.

1.2 Record of revisions

2.0 Specification

2.1 Type Designation

Explains the designation system for engine types.

2.2 Cylinder Marking

3. Technical Data

3.1 Dimensions and Weights

Provides dimensions and weight specifications for the engine.

3.2 Engine Accessories

Lists and describes engine accessories.

3.5 Fuels and Lubricants

Information on fuels and lubricants for the engine.

3.3 Performance

3.4 Engine Speed

4.0 Power Characteristics

5.0 Operating Instruction

5.1 Before Starting the Engine

Pre-start checks and procedures for the engine.

5.2 Engine Starting

Step-by-step guide for starting the engine.

5.3 Warm-up and Increasing Power Setting

5.4 Take-off

5.5 Cruising Flight

5.6 Engine Shutdown

5.7 In-flight Engine Shutdown

5.8 In-flight Engine Starting

5.9 Note

6. Instruction for Maintenance

6.1 Daily Check

Daily checks to be performed before flight.

6.2 Periodic Check

Intervals and procedures for periodic inspections.

6.3 List of works during periodic checks

6.3 List of works during periodic checks (cont.)

Major inspection of the engine

6.4 Servicing Prior to the First Engine Starting

6.5 Inspection After the First 25 Hours of Operation

6.6 Engine Preservation

6.7 Winter Operation

7.0 MAINTENANCE

7.1 Oil Change

Procedure for changing engine oil.

7.2 Compression Check

Method for checking engine compression.

7.3 Valve Clearance Adjustment

7.4 Adjustment of Ignition Timing

7.5 Spark Plugs

7.6 Carburetter

7.7 Exhaust System

7.8 Screws and Nuts

7.9 Bowden Cables and Engine Control Linkages

7.10 Alternator

8.0 REPAIR

8.1 Overhaul

Engine overhauls must be done by the manufacturer.

8.2 Major Maintenance and Repair

Major maintenance and repairs by authorized stations.

9.0 TABLE OF OILS

10.0 TIGHTENING TORQUE TABLE

11.0 Troubleshooting

11.1 Defect: Engine Not Starting

Lists causes and remedies for engine not starting.

11.2 Defect: Irregular Engine Run

Lists causes and remedies for irregular engine running.

11.3 Defect: Engine Vibration

11.4 Defect: Rough Engine Run

11.5 Defect: Engine Overheat

11.6 Defect: Exhaust Gas Firing or Black Exhaust Gas

11.7 Defect: Engine Backfire

11.8 Defect: Engine Not Delivering Full Power

11.9 Defect: Low Oil Pressure

11.10 Defect: Ignition

11.11 Defect: Electrical Accessories

12.0 ANNEXES

12.1 Carburetter Drawing

Diagram of the carburetter with key components labeled.

12.2 Ignition Magnetos Repairs, Disassembly and Assembly

PARMA-TECHNIK MIKRON III A Specifications

General IconGeneral
BrandPARMA-TECHNIK
ModelMIKRON III A
CategoryEngine
LanguageEnglish