Particle Measuring Systems LASAIR II 310 Operator's Manual


Installing the LASAIR IIInstalling the LASAIR II
LASAIR II Operator’s ManualLASAIR II Operator’s Manual
PagePage
2-32-3
44
Turn the battery retainer to a horizontal position.Turn the battery retainer to a horizontal position.
55 With the battery contacts entering first and the battery label facing up, slide theWith the battery contacts entering first and the battery label facing up, slide the
battery pack into the LASAIR II’battery pack into the LASAIR II’s battery chamber until it stops.s battery chamber until it stops.
66
Rotate the battery retainer to a vertical position. The retainer’s edge shouldRotate the battery retainer to a vertical position. The retainer’s edge should
engage into a provided channel.engage into a provided channel.
77
Ensure that the battery is firmly in place by Ensure that the battery is firmly in place by tipping the LASAIR II or by tryingtipping the LASAIR II or by trying
to pull the battery out without turning the to pull the battery out without turning the battery retainer to a horizontalbattery retainer to a horizontal
position.position.
88
Close the battery chaClose the battery chamber door.mber door.
NOTE:NOTE: TTo completely remove o completely remove LASAIR II power, the battery pack LASAIR II power, the battery pack must bemust be
removed.removed.
Connecting the Sample Probe, 310 Connecting the Sample Probe, 310 and 510 Versionsand 510 Versions
The LASAIR II comes with a standard sample probe, which can be connectedThe LASAIR II comes with a standard sample probe, which can be connected
in one of the following two ways:in one of the following two ways:
•• directly to the sample inletdirectly to the sample inlet
••
to the end of sample tubing that is connected to the sample inletto the end of sample tubing that is connected to the sample inlet
The sample tubing included The sample tubing included in your shipment is lined internally with a in your shipment is lined internally with a materialmaterial
that reduces electrostatic attraction and subsequent particle sticking. Cut it tothat reduces electrostatic attraction and subsequent particle sticking. Cut it to
the length that meets your needs. the length that meets your needs. It will fit over the sample inlet.It will fit over the sample inlet.
NOTE:NOTE: If the sample tubing is longer than 10 If the sample tubing is longer than 10 feet (3.05 meters), Particlefeet (3.05 meters), Particle
Measuring Systems cannot guarantee valid particle measurement.Measuring Systems cannot guarantee valid particle measurement.
ALSOALSO: If you intend to sample for particles greater than 5: If you intend to sample for particles greater than 5 µµm, you should notm, you should not
use any tubing at all.use any tubing at all.
For precise positioning and proper cleanroom isolation, you For precise positioning and proper cleanroom isolation, you may choose tomay choose to
mount the sample probe on a mount the sample probe on a tripod or on a wall. The following accessories willtripod or on a wall. The following accessories will
help you to precisely position your LASAIR help you to precisely position your LASAIR II:II:
•• A floor tripod (Part No. MI008)A floor tripod (Part No. MI008)
•• A table tripod (Part No. 1000000979)A table tripod (Part No. 1000000979)
••
A wall mount adaptor for the Standard Sampling Probe A wall mount adaptor for the Standard Sampling Probe (Part No.(Part No.
1000000971)1000000971)
•• A Sampling Probe, Isokinetic, with wall/hand/tripod adapter (Part No.A Sampling Probe, Isokinetic, with wall/hand/tripod adapter (Part No.
90103070) from Particle Measuring Systems.90103070) from Particle Measuring Systems.
To connect the sample probe directly to the sample inlet:To connect the sample probe directly to the sample inlet:
11 Remove the protective cap from the Remove the protective cap from the sample inlet. Place the sample probesample inlet. Place the sample probe
directly over the black polyethylene sample inlet, located on the top of the directly over the black polyethylene sample inlet, located on the top of the unit.unit.

Particle Measuring Systems LASAIR II 310 Specifications

General

Brand	Particle Measuring Systems
Model	LASAIR II 310
Category	Measuring Instruments
Language	English