2 • EVERPURE
®
PRO-Reverse Osmosis Water Filtration System Installation and Operating Instructions
TABLE OF CONTENTS
Operating Specifications ......................................................2
System Dimensions .............................................................2
Production Capabilities........................................................2
Tools Required .....................................................................3
Precautions .......................................................................... 3
How Reverse Osmosis Works ..............................................4
Installation ..........................................................................5
System Startup ..................................................................11
Testing Your Reverse Osmosis System ..............................12
Maintenance .......................................................................12
Troubleshooting .................................................................14
Performance Data ..............................................................16
California Proposition 65 Warning .....................................17
Replacement Parts ............................................................18
OPERATING SPECIFICATIONS
IMPORTANT! Before installing this reverse osmosis system,
make certain your water supply complies with the following
operating specifications. Failure to comply may reduce the
effectiveness of the system and will void the warranty. Consult
your local water treatment utility or a certified water testing
lab to determine the quality for your water and use the table
below to record your results for future reference.
Specifications Your Water
Pressure Range: 40–100 psi
(2.7–6.9 bar)
Temperature
Range:
40–100°F
(4.4–37.8°C)
Total Dissolved
Solids: <1500 ppm
Maximum
Hardness †: 10gpg (171 mg/L)
Sulfide, Iron and
Manganese‡: <0.01 ppm
Chlorine in Water
Supply: <2 ppm
Water Supply pH
Limits: 4–11
Turbidity: 1 NTU Max
Model #
Date of Purchase:
†IMPORTANT: If the hardness of your water is above 10 gpg
(171 mg/L), lime scale will build up rapidly on the membrane
inside of the RO membrane cartridge. Scale buildup will plug
the RO membrane cartridge and make the system ineffective.
We do not recommend these reverse osmosis systems be used
with water in excess of 10 gpg (171 mg/L) hardness, unless the
water is softened prior to the reverse osmosis system.
‡See your local dealer or water treatment specialist to reduce
these substances in your water.
NOTE: If your water pressure and temperature are at the
low end of the listed range (40 psi [2.8 bar] and 40°F
[4.4°C]), and the TDS level is near the maximum
(1500 ppm), the system will not function properly.
Under these extreme conditions, pre-warming the
supply water using a 25 feet (7.62 m) coil of tubing
between the supply adapter and the system, and/
or installing a booster pump to increase the water
pressure will allow the system to perform effectively.
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system.
Systems certified for cyst reduction may be
used on disinfected waters that may contain
filterable cysts.
NOTE: Substances reduced are not necessarily in your
water. System must be maintained according to
manufacturer’s instructions, including replacement
of filter cartridges.
SYSTEM DIMENSIONS
System Dimensions: 13.75 inches W x 4.75 inches D x
12.75 inches H
(349 mm x 121 mm x 318 mm)
System Weight: 6.1 lbs. (2.7 kg)
Tank Dimensions: 11.3 inches Dia x 16.75 inches H
(287 mm x 425 mm) (with valve)
Tank Capacity: 1.9–3.2 gallons (7.2–12.1 L)
(depending on water pressure)
Tank Weight (full): 40 lbs. (18.2 kg.)
(depending on water pressure)
PRODUCTION CAPABILITIES
Tested by NSF International according to NSF/ANSI Standard 58
has given 5.7 gallons per day. Source water test parameters are
50 psig, 77ºF, pH of 7.5 ± 0.5 and 750 ppm total dissolved solids.
The PRO is Tested and Certified by NSF
International against NSF/ANSI Standard 58 for
the reduction of Total Dissolved Solids, Fluoride,
Turbidity, Nitrate/Nitrite, Lead, Selenium,
Pentavalent Arsenic, Copper, Cadmium,
Hexavalant Chromium, Trivalent Chromium,
Barium, Cysts, Radium 226/228 and NSF/ANSI
Standard 42 for the reduction of chlorine taste
and Odor.
NSF ANSI Standard 58 certified to reduce cysts such
as Cryptosporidium and Giardia by mechanical means.
EPA Est. No 090375-MEX-001
To Next Page
Loading...
