Pentair QC10-CBR - Product Specifications; General System Specs & Model Data; Included and Required Items

SPECIFICATIONS
Pressure Range: 30–125 psi (2.1–8.62 bar)
Temperature Range: 40–100°F (4.4–37.8°C)
Rated Service Flow:
QC10-CBR 0.5 gpm (1.9 Lpm)
QC10-EP 0.5 gpm (1.9 Lpm)
QC10-GAC 0.75 gpm (2.8 Lpm)
QC10-TSGAC 0.75 gpm (2.8 Lpm)
QC10-CGAC* 0.6 gpm (2.3 Lpm)
QC10-CB1* 0.6 gpm (2.3 Lpm)
Size: 2.187-inch x 11.625-inch
(55.5 mm x 295.3 mm)
*Not Performance Tested or Certified by NSF.
PARTS INCLUDED
• Filter head with built-in bracket and compression or
push-fit fittings
• Cartridge
• Hardware kit
TOOLS AND MATERIALS REQUIRED
• Phillips screwdriver
• Adjustable wrench (for 1/4-inch male threaded parts)
• Tape measure
• Pencil
• Safety glasses
• Separate drinking water faucet required if supplying
water directly to the kitchen sink
OPTIONAL MATERIALS
• Shut-off valve
• Saddle tap valve with shut-off
• Threaded copper "T"
• 1/4-inch (6.35 mm) plastic or copper tubing or flexible hose
• 3/8-inch (9.53 mm) plastic or copper tubing or flexible hose
The QC10-CBR is Tested and Certified by NSF
International to NSF/ANSI Standard 42/53.
The QC10-EP is Tested and Certified by NSF
International to NSF/ANSI Standard 42 for the
aesthetic reduction of Chlorine Taste and Odor.
The QC10-GAC is Tested and Certified by NSF
International to NSF/ANSI Standard 42 for the
aesthetic reduction of Chlorine Taste and Odor.
The QC10-TSGAC is Tested and Certified by NSF
International to NSF/ANSI Standard 42 for the
aesthetic reduction of Chlorine Taste and Odor.
PRECAUTIONS
WARNING:
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system.
CAUTION
Protect against freezing to prevent cracking of the
filter and water leakage.
CAUTION
Because of the product’s limited service life and to
prevent costly repairs or possible water damage,
we strongly recommend that the head of the filter
be replaced every ten years. If the head of your
filter has been in use for longer than this period,
it should be replaced immediately. Date the top of
any new head to indicate the next recommended
replacement date.
CAUTION
Turn off water supply to head without cartridge if
it must be left unattended for an extended period
of time.
PRODUCT SPECIFICATIONS
Model Claims Filter Capacity
Rated
Service
Flow
Micron
Rating
1/4-inch
Threaded
1/4-inch
JG
Push fit
3/8-inch
JG
Push fit
Replacement
Cartridge
QC10-CBR
chlorine taste & odor,
sediment, lead, atrazine,
lindane, cysts** and turbidity
500 gallons
(1,890 L)
0.5 gpm
(1.9 L/min)
0.5 158667 158682 158691
QC10-CBRR
155785-43
QC10-EP chlorine taste & odor
1,500 gallons
(5,670 L)
0.5 gpm
(1.9 L/min)
5* 158668 158683 158692
QC10-EPR
155962-43
QC10-GAC chlorine taste & odor
2,500 gallons
(9,460 L)
0.75 gpm
(2.8 L/min)
– 158669 158684 158693
QC10-GACR
155901-43
QC10-TSGAC
chlorine taste & odor with
phosphate crystals
1,700 gallons
(6,435 L)
0.75 gpm
(2.8 L/min)
– – 158723 158724
QC10-TSGACR
255706-43
QC10-CGAC*
chloramine taste & odor and
chlorine taste & odor*
500 gallons
(1,890 L)*
0.6 gpm
(2.3 L/min)*
– – 158719 158720
QC10-CGACR
255704-43
QC10-CB1
chlorine taste & odor and
sediment*
10,000 gallons
(37,850 L)*
0.6 gpm
(2.3 L/min)*
- – 158721 158722
QC10-CB1R
255705-43
Turbidity = 5 NTU Max.
*Not Performance Tested or Certified by NSF.
**NSF/ANSI Standard 53 certified to reduce cysts such as
Cryptosporidium and Giardia by mechanical means.
2 •PENTEK
®
QC10 SERIES Installation and Operation Manual