Why is the airflow weak in my Philips AC2729?
If the airflow from your Philips Air Cleaner is weaker than usual, the pre-filter may be dirty; clean it. Also, ensure all packaging material has been removed from the NanoProtect filter.
Why does my Philips AC2729 smell bad?
When you first use your Philips Air Cleaner, a plastic smell may occur, which is normal. However, if a burnt smell persists (even after removing the filters), contact your Philips dealer or an authorized Philips service center. Alternatively, if the filter produces an odor after use, remove it and place it in direct sunlight with ventilation for several hours. If the odor persists, replace the filter.
Why is my Philips AC2729 Air Cleaner not improving air quality?
If the air quality doesn't improve even after prolonged use of your Philips Air Cleaner, ensure all packing material is removed from the filters. Also, check that all filters are installed correctly in the following order: 1) NanoProtect filter Series 3 (FY1410); 2) NanoProtect filter Active Carbon (FY1413); 3) pre-filter. A wet air quality sensor can also be the cause, so ensure it is clean and dry.
How to reset filter replacement indicator on Philips AC2729?
If your Philips Air Cleaner still indicates a filter replacement is needed after you've replaced it, ensure you correctly touched and held the Timer/Reset button. Plug in the appliance, switch it on, and then touch and hold the Timer/Reset button for 3 seconds.
What to do if Philips Air Cleaner does not work when switched on?
If the Philips Air Cleaner does not work even when switched on, check if the child lock is activated.
Why Philips AC2729 does not work even if plugged in?
If the Philips Air Cleaner does not work even though it is plugged in, ensure the water tank is properly installed and contains enough water if the water refill light is flashing. If the filter replacement light is flashing and you haven't replaced the NanoProtect filter, the appliance may be locked. In this case, replace the filter and reset the filter lifetime counter.
What to do if Philips Air Cleaner doesn't work when switched on?
If your Philips Air Cleaner does not work even when switched on, check if the child lock is activated, as this may prevent the buttons from responding.
General safety instructions and warnings for using the appliance.
Lists and identifies all parts of the air purifier with corresponding labels.
Details the functions of control buttons and display panel indicators.
Step-by-step guide on how to install the NanoProtect filter correctly.
Instructions for setting up the humidification function, including water tank preparation.
Guide for connecting the air purifier to a Wi-Fi network via the "Air Matters" app.
Explains the meaning of different air quality light colors and their corresponding PM2.5 levels.
Instructions on how to power the appliance on and off.
How to adjust the desired humidity level for the room.
Explains how to switch between purification-only and 2-in-1 modes.
Details how to dim or turn off the appliance's lights and display.
How to cycle through different display modes like PM2.5, IAI, and humidity.
Guide to selecting between Auto, Allergen, and Sleep modes.
How to manually adjust the fan speed to different levels.
Instructions on setting the appliance to operate for a specific duration.
How to activate and deactivate the child lock feature.
Information about checking the water level and the water refill alert.
Recommended frequency and methods for cleaning different parts of the appliance.
How to clean the exterior surfaces and air outlet of the purifier.
Step-by-step guide to cleaning the air quality sensor for accurate readings.
Detailed instructions for cleaning these specific components regularly.
How to clean the pre-filter, including when the alert is shown.
Procedure for removing limescale buildup from the humidification wick using cleaning agents.
Explains the lock feature that ensures filters are replaced for optimal operation.
Step-by-step guide for replacing the NanoProtect filter, including filter alert indicators.
Instructions for replacing the NanoCloud humidification wick, guided by filter alerts.
Where to get information, order parts, or contact customer service.
Information regarding the appliance's compliance with electromagnetic field standards.
Guidelines for proper disposal and recycling of the product at its end of life.
Legal notices regarding app trademarks and open-source software used.
General| Control type | Touch |
|---|---|
| Product color | Black, White |
| Built-in display | Yes |
| Housing material | Acrylonitrile butadiene styrene (ABS) |
| Efficiency | 99.97 % |
| Motor type | DC |
| Cord length | 1.8 m |
| Noise level | - dB |
| Air purify rate | 250 m³/h |
| Number of modes | 3 |
| Number of speeds | 4 |
| Country of origin | China |
| Timer duration (maximum) | 12 h |
| Timer duration (minimum) | 1 h |
| Suitable for room area up to | 65 m² |
| Filters out bacteria | 99.9 % |
| AC input voltage | 220 V |
| AC input frequency | 50 Hz |
| Package depth | 446 mm |
| Package width | 310 mm |
| Package height | 695 mm |
| Package weight | 9.9 g |
Weight and Dimensions| Depth | 396 mm |
|---|---|
| Width | 230 mm |
| Height | 580 mm |
To Next Page