Philips HDP1650TV - User Manual

Questions and Answers

R
Rachel HollandAug 18, 2025
What to do if my Philips HDP1650TV only shows the initial screen?
- R
  robin08Aug 18, 2025
  If your Philips Projector only shows the initial screen, check the following: * Ensure the cables are connected to the correct sockets. * Verify that the external device is switched on. * Confirm that the video output of the external device is activated. * Make sure the HDMI source selected on the user interface corresponds to the HDMI connector where the external device is connected.
A
andreamckeeAug 20, 2025
What to do if my Philips HDP1650TV only shows the initial screen from computer?
- T
  Taylor RobinsonAug 20, 2025
  If your Philips Projector only shows the initial screen when connected to a computer, ensure that the VGA output of the computer is switched on. Also, verify that the computer's resolution is set to 1280*800 for VGA connections or 1080P for HDMI connections.
T
Tyler ClarkAug 23, 2025
What to do if my Philips HDP1650TV Projector has no sound from external HDMI device?
- M
  Melissa PeckAug 23, 2025
  If there is no sound from the external device connected to your Philips Projector, check the cables connected to the external device. Also, ensure the volume is set correctly on the external device and only use the original cables from the device manufacturer.
L
Lauren WebbAug 26, 2025
Why does my Philips HDP1650TV turn itself off?
- W
  wfryAug 26, 2025
  Your Philips Projector may turn off automatically if it overheats after running for a long time; a warning symbol will appear on the projection. Ensure the power cable is correctly connected and check the sleep mode status in the setting menu. If sleep mode is activated, the device will turn off after the programmed duration. After the device has cooled down, you can continue playback.
A
Angela WrightAug 28, 2025
How to fix bad image quality on Philips HDP1650TV Projector with HDMI?
- S
  Sarah JohnstonAug 28, 2025
  If you are experiencing bad image or color quality with your Philips Projector when connected via HDMI, try using a high-quality HDMI cable. Low-quality cables can cause signal distortions.
C
Christine ChoiAug 31, 2025
What to do if my Philips Projector cannot read the USB stick?
- M
  meyeralexisAug 31, 2025
  If your Philips Projector cannot read the USB stick, it might be because the device does not support the exFAT file system. Format the USB key in FAT format and try again.
S
Sean RamirezSep 2, 2025
Why my Philips HDP1650TV Projector changes brightness when playing videos from USB?
- G
  gordonamySep 2, 2025
  Your Philips Projector may automatically reduce brightness to protect the high-power LED if the environment temperature is too high. Try using the device in lower environment temperatures.
I
Isabel PetersonSep 4, 2025
How to fix Philips HDP1650TV Projector not reacting to remote control?
- S
  Steven WilkersonSep 5, 2025
  If your Philips Projector does not react to the remote control, check if the remote control batteries are new. If not, replace them. The remote control may need to be paired with the USB receiver again. To renew the pairing, connect the USB receiver to a rear USB port of the projector, then press the red and blue keys on the remote control simultaneously for 5 to 10 seconds.
T
Tina MillerSep 7, 2025
What to do if Philips Projector doesn't switch on?
- H
  hectorcarterSep 7, 2025
  If your Philips Projector cannot be switched on, disconnect and reconnect the power supply cable and try again.
D
David DavisSep 10, 2025
What to do if Philips Projector cannot be switched off?
- J
  Jack OrozcoSep 10, 2025
  If your Philips Projector cannot be switched off, disconnect the power supply cable.