Philips HDR3700/05 - Channel Management and Tuning

84
EN
This unit can receive the Hyper and Oscar
frequency bands.
• To set “Skip” to “ON”, select “Skip” using
[U \ D], then press [P]. Select “OFF” using
[U \ D], then press [L].
• If you want to decode scrambled signals, select
“Decoder” using [U \ D], then press [P]. Select
“ON” using [U \ D], then press [L].
• To store another channel, repeat steps
5 to 8.
9 Press [HOME] to exit.
You can set the unit to skip channels. You can no
longer receive or watch when you access channels
using [PROGRAM + / –].
1 Follow steps 1 to 4 in “Manual
Tuning (ANALOG)” on page 83.
2 Select “Position” using [U \ D],
then press [P].
3 Select the position number you want
to skip using [Alphanumeric keypad]
or [U \ D], then press [L].
4 Select “Skip” using [U \ D], then
press [P].
5 Select “ON” using [U \ D], then
press [L].
• To skip another channel, repeat steps 2 to 5.
6 Press [HOME] to exit.
You can change the order of the stored channels
according to your preference.
1 In stop mode, press [HOME]. Select
“General Settings” using [U \ D],
then press [OK].
2 Select “Channel” using [U \ D],
then press [OK].
3 Select “Analog Channel Setup”
using [U \ D], then press [OK].
4 Select “Sort Channels” using
[U \ D], then press [OK].
5 Select the preset number of the
channel you want to change using
[U \ D], then press [OK].
• “ ✔ ” will be displayed on the left side of “Pos. CH”.
• You cannot select a position number where
“– – –” appears next to the number, because
“Skip” is set to “ON” for that position number.
6 Move the channel to another
position number using [U \ D], then
press [OK].
• To move another channel, repeat steps 5 to 6.
7 Press [HOME] to exit.
You can programme the tuner to scan only the digital
channels that you can receive in your area.
1 In stop mode, press [HOME]. Select
“General Settings” using [U \ D],
then press [OK].
2 Select “Channel” using [U \ D],
then press [OK].
3 Select “Digital Channel Setup” using
[U \ D], then press [OK].
4 Select “Auto Tuning” using [U \ D],
then press [OK].
The unit will start storing channels available in
your area.
The tuner scans and memorises all the active
digital channels (TV / Radio) in your area.
•Press [OK] after Auto Tuning is completed, then
the digital channel at lowest preset will appear
on the screen.
5 Press [HOME] to exit.
You can use [PROGRAM + / –] to access the
stored digital channels.
Note
• If you press [BACK U] during the scanning,
the screen will return to the previous displayed
menu, and Auto Tuning will be cancelled.
• If you press [HOME] during the scanning, this
operation will stop and the lowest number of
digital channels will appear on the TV screen.
Skip a Preset Channel
ANALOG
Sort Channels (ANALOG)
ANALOG
Auto Tuning (DIGITAL)
DIGITAL
General Settings
Channel
Digital Channel Setup
Digital&Analog Tuning
Digital Channel Setup
Analog Channel Setup
Manual Tuning
Edit Channels
Signal Information
Auto Tuning
1 ITV1
2 ITV2
3
4 E4
Channel48 UHF
700 BBC Radio 1
701 BBC Radio 2
702 Magic Radio
703 Classic FM
690000kHz/8M
60%
Channel search
TV channelS.No. Radio channelS.No.
Progress
Channel
E2N41BN_EN.book Page 84 Wednesday, July 2, 2008 4:36 PM