Additional information
13
118
En
No sound
During loud playback the
power suddenly switches off.
• Turn down the volume.
• Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 101.
• Switch on the digital safety feature. While holding down ENTER on the front panel, press
STANDBY/ON to set this receiver to the standby mode. Use TUNE / to select D.SAFETY
OFF, and then use PRESET / to select 1 or 2 (select D.SAFETY OFF to deactivate this
feature). If the power switches off even with 2 switched on, turn down the volume. With 1 or 2 on,
some features may be unavailable.
The receiver suddenly switches
off or the iPod iPhone
indicator blinks.
• Check that there are no loose strands of speaker wire touching the rear panel or another se
t of
wires. If so, re-attach the speaker wires, making sure there are no stray strands.
• The receiver may have a serious problem. Disconnect from the power and call a Pioneer authorized
independent service company.
AMP ERR blinks in the display,
then the power automatically
switches off. The ADVANCED
MCACC blinks and the power
does not turn on.
• The receiver may have a serious pr oblem. Do not try switching the receiver on. Unplug the receiver
from the wall and call a Pioneer authorized independent service company.
The PQLS flashes and power
turns off.
• There is a problem with the receiver’s power unit
or fan. Try turning on the power. If the same thing
happens, the receiver is damaged. Unplug the receiver from the wall and call a Pioneer authorized
independent service company. (Other symptoms may appear when the power is turned on.)
FAN STOP blinks in the
display, then the power
automatically switches off and
the PQLS indicator blinks.
• Something is obstructing the fan. Remove the obstruction and try switching the receiver back on.
If the fan is still not working, or you can’t remove the object, unplug the receiver from the wall and
call a Pioneer authorized independent service company.
• The fan is malfunctioning. Unplug the receiver from the wall and call a Pioneer authorized
independent service company.
OVERHEAT blinks in the
display or AMP OVERHEAT
and the STANDBY/ON
indicator flash and the power
turns off.
• Allow the unit to cool down in a well-ventilated place before switching back on.
• Wait at least 1 minute, then try turning the power on again.
The receiver suddenly power
off or ADVANCED MCACC
flashes.
• The power unit is damaged. Unplug the receiver from the wall and call a Pioneer authorized
independent service company.
Display blinks 12V TRG ERR.• An error has arisen in the 12 V trigger jacks. Reconnect accurately then turn the power back on.
Symptom Remedy
No sound is output when an
input function is selected.
No sound is output from the
front speakers.
• Check the volume, mute setting (press MUTE) and speaker setting (press SPEAKERS).
• Make sure the correct input function is selected.
• Check that the MCACC setup microphone is disconnected.
• Make sure the correct input signal is selected (press SIGNAL SEL). Note that when PCM is
selected, you won’t be able to hear any other signal format.
• Check that the source component is connected properly (see Connecting your equipment on
page 19).
• Check that the speakers are connected properly (see Connecting the speakers on page 23).
No sound from the surround or
center speakers.
• Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t selected;
select one of the surround listening modes (see Listening in surround sound on page 55).
• Check that the surround/center speakers are
not set to NO (see Speaker Setting on page 110).
• Check the channel level settings (see Channel Level on page 111).
• Check the speaker connections (see Connecting the speakers on page 23).
No sound from surround back
speakers.
• Check that the surround back speakers are set to LARGE or SMALL, and the surround speakers
are not set to NO (see Speaker Setting on page 110).
• Check the speaker connections (see Connecting the speakers on page 23). If only one surround
back speaker is connected, make sure it’s connected to the left channel speaker terminal.
• Surround back speakers will not play while the Speaker System is set to Speaker B and audio is
being played through speaker B.
Symptom Remedy
SC-LX83_73_DLPW.book 118 ページ 2010年5月19日 水曜日 午後2時7分