Pioneer UDP-LX500 User Manual

07
44
En
❖ Setting the IP address
1 Select and set Network  IP Address Setting 
Next Screen.
Use / to select, then press ENTER.
2 Set IP address.
Use / / / to set the IP address of the player
or DNS server, then press ENTER.
• Auto Set IP Address
On – The player’s IP address is obtained
automatically. Select this when using a
broadband router or broadband modem that
has a DHCP (Dynamic Host Configuration
Protocol) server function. This player’s IP
address will automatically be allocated from
the DHCP server.
Off – The player’s IP address must be set
manually. Use the number buttons (0 to 9) to
input the IP address, subnet mask and default
gateway.
Caution
• Some time is required for the IP address
setting.
Note
• Once the IP address is set, select [Connection
Test] to check that the unit is properly
connected.
• For information on the DHCP server function,
refer to the operating instructions for the
network device.
• You may need to contact your Internet service
provider or network administrator when
inputting the IP address manually.
❖ Setting the proxy server
Only set the proxy server if so instructed by your
Internet service provider.
1 Select and set Network  Proxy Server  Next
Screen.
Use / to select, then press ENTER.
2 Select and set Use or Not use at Proxy Server.
Use / to change, then press .
• Use – Select this when using a proxy server.
• Not use – Select this when not using a proxy
server.
If you have selected Use, proceed to step 3.
3 Select and set Server Select Method.
Use / to change, then press .
• IP Address – Input the IP address.
• Server Name – Input the server name.
4 Input IP Address or Server Name.
Use the number buttons (0 to 9) to input the
number if you select IP address in step 3. Use /
to move the cursor.
When Server Name is selected in step 3, use the
number buttons (0 to 9) to launch the software
keyboard. Now use / / / to select
characters and items, then press ENTER to input.
5 Input Port Number.
Press , then use the number buttons (0 to 9)
to input the number.
6 Press ENTER to set.
❖ Displaying the network settings
 Select and set Network  Information  Next
Screen.
Use / to select, then press ENTER.
The MAC address, IP address, subnet mask, default
gateway and DNS server (primary and secondary)
settings are displayed.
When Auto Set IP Address is set to On, the values
obtained automatically are displayed.
Note
• “0.0.0.0” is displayed when each IP address has
not been set.
❖ Testing the network connection
 Select and set Network  Connection Test 
Start.
Use / to select, then press ENTER.
“Network is OK.” is displayed once the test is
completed. If any other message is displayed,
check the connections and/or settings (page 22
and page 44).
❖ Changing to other language at
language setting
1 Select and set Language.
Use / to select, then press ENTER.
2 Select and set OSD, Audio, Subtitle or Menu.
Use / to select, then press ENTER.
3 Select and set the desired language.
Use / to select, then press ENTER.
Note
• If a language not recorded on the BD/DVD is
set, one of the recorded languages is
automatically selected and played.

Pioneer UDP-LX500 Specifications

General

3D	-
Device type	Blu-Ray player
Cassette deck	No
Product color	Black
USB 2.0 connectors	2
Firmware upgradeable	Yes
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
AC input voltage	110 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.45 W
Power consumption (typical)	28 W
Playback disc types	BD-R, BD-R DL, BD-RE, BD-RE DL, CD, CD-R, CD-ROM, CD-RW, DVD, DVD+R, DVD+R DL, DVD+RW, DVD-R, DVD-R DL, DVD-RW
Disc types supported	BD, BD-R, BD-R DL, BD-RE, BD-RE DL, CD, CD-DA, CD-R, CD-ROM, CD-RW, DVD, DVD+R, DVD+R DL, DVD+RW, DVD-R, DVD-R DL, DVD-RW
Playback disc formats	CD audio, DVD-Audio, DVD-Video

Weight and Dimensions

Depth	337 mm
Width	435 mm
Height	118 mm
Weight	10300 g