Powtran PI500-S 022G3

Questions and Answers

T
timothy18Nov 21, 2025
What to do if my Powtran Inverter displays Err.02?
- C
  Christopher HarrisNov 21, 2025
  If the Powtran Inverter shows Err.02, it could be due to several reasons: * The acceleration time might be too short, in which case you should increase it. * The manual torque boost or V/F curve might be unsuitable, so adjust them. * Low voltage can cause this, so set the voltage to the normal range. * A short-circuit or earthing of the inverter output requires you to eliminate peripheral faults. * If using vector control mode without parameter identification, perform identification for the motor parameters. * If the motor starts unexpectedly while rotating, select Speed Tracking Start or restart after stopping the motor. * A sudden increase in load during acceleration may trigger this, so cancel the sudden load. * If the inverter type is too small, choose one with a large...
T
Tracy BartlettAug 25, 2025
What causes Err.03 on a Powtran PI500-S 022G3 and how to fix it?
- A
  Ashley WellsAug 26, 2025
  The Err.03 error on your Powtran Inverter can arise from several factors. Here's what to check: * A short-circuit or earthing of the inverter output. If this is the case, eliminate peripheral faults. * If you're using vector control without identifying parameters, perform motor parameter identification. * A deceleration time that's too short. Increase the deceleration time. * Low voltage can cause this error. Set the voltage to the normal range. * If the load suddenly increases during deceleration, cancel the sudden load. * Lack of a braking unit and braking resistor. Install a braking unit and brake resistor.
Z
Zachary WongAug 27, 2025
Why does my Powtran PI500-S 022G3 show Err.04?
- J
  John JeffersonAug 27, 2025
  The Err.04 error on a Powtran Inverter can be attributed to the following reasons: * A short-circuit or earthing of the inverter output. If this occurs, eliminate peripheral faults. * If the control mode is vector and parameters haven't been identified, perform identification for the motor parameters. * Low voltage can trigger this error; set the voltage to the normal range. * A sudden increase in load during operation may also cause it; cancel the sudden load. * If the inverter type is too small, select an inverter with a larger power level.
C
Caroline OchoaAug 27, 2025
What does Err.05 mean on my Powtran Inverter?
- K
  Katelyn PerezAug 27, 2025
  If your Powtran Inverter displays Err.05, consider the following potential causes and solutions: * If a braking unit and braking resistor haven't been installed, install them. * High input voltage can cause this error. Set the voltage to the normal range. * External force dragging the motor during acceleration can trigger this. Cancel the external force or install a braking resistor. * If the acceleration time is too short, increase it.
J
joseph95Aug 29, 2025
How do I fix Err.06 on my Powtran PI500-S 022G3?
- T
  troyobrienAug 29, 2025
  If you're seeing Err.06 on your Powtran Inverter, here's what you should check: * High input voltage. Set the voltage to the normal range. * External force dragging the motor during deceleration. Cancel the external force or install a braking resistor. * A deceleration time that's too short. Increase the deceleration time. * Missing braking unit and braking resistor. Install a braking unit and brake resistor.
C
Christina RiveraSep 18, 2025
What does Err.22 mean on Powtran Inverter?
- A
  Andre FisherSep 18, 2025
  If your Powtran Inverter displays Err.22, it means there is an overvoltage or overcurrent. Eliminate the overvoltage or overcurrent fault.
B
barrettmckenzieSep 15, 2025
What does Err.15 on Powtran PI500-S 022G3 Inverter mean?
- R
  Rebecca BonillaSep 15, 2025
  If your Powtran Inverter is displaying Err.15, it means an external fault signal was input through the multi-function terminal DI. Reset run.
D
Debbie RodriguezSep 17, 2025
What does Err.21 mean on Powtran PI500-S 022G3 Inverter?
- E
  Elizabeth ByrdSep 18, 2025
  If your Powtran Inverter displays Err.21, it indicates that the EEPROM chip is damaged. Replace the main control panel.
T
Tina ScottSep 7, 2025
What to do if Powtran Inverter shows Err.12?
- T
  Terry Johnson Jr.Sep 7, 2025
  If your Powtran Inverter displays Err.12, it could be due to: * An abnormal drive panel. Replace the drive, the power board or contactor. * An abnormal lightning protection plate. Seek technical support. * An abnormal main control panel. Check and eliminate the existing problems in the peripheral line.
M
Matthew GonzalezSep 5, 2025
What does it mean when my Powtran PI500-S 022G3 shows Err.11?
- C
  christophermossSep 5, 2025
  If your Powtran Inverter is displaying Err.11, consider these possibilities: * The power grid voltage might be too low. Check the power grid voltage. * The motor protection parameters (F8.03) might not be set appropriately. Correctly set this parameter. * The load could be too large, or the motor might be stalling. Reduce the load and check the motor and its mechanical condition.