Procon A1M - 5 Setpoint Offset; Settings; Operation

5. Setp
o
The Setpoin
t
5.1. S
e
There are tw
o
Setpoint.
The BMS Vi
r
if the Melco
B
The BMS R
o
lost and res
e
5.2. O
p
In some situ
a
accurate te
m
between the
s
The new te
m
Temperatur
e
As a hypoth
e
temperature
increases th
e
When the B
M
Hysteresis h
a
o
int Off
s
t
Offset featur
e
e
ttings
o
settings whi
r
tual Setpoint
c
B
EMS MINI (
A
o
om Tempera
t
e
t to zero upo
n
p
eration
a
tions a 3
rd
p
a
m
perature rea
d
s
e two tempe
r
m
perature set
p
e
Setpoint =
R
e
tical exampl
e
remaining co
n
e
indoor unit’s
M
S Room Te
m
a
s been built i
s
et
e
is only appli
c
ch are applic
a
c
an be chang
e
A
1M) loses po
w
t
ure can be c
h
n
the MelcoB
E
a
rty room tem
p
d
ing than the
r
r
ature reading
p
oint is calcul
a
R
eturn Air T
e
e
, consider th
e
n
stant at 22º
C
temperature
m
perature rea
c
n to prevent t
h
c
able to, and
w
a
ble to the Se
t
e
d using Mod
b
w
er.
h
anged using
M
E
MS MINI (A1
p
erature sens
o
r
eturn air tem
p
s and compe
n
a
ted using the
e
mperature –
e
BMS Virtual
S
C
. As the BMS
s
etpoint.
c
hes 18ºC th
e
h
e temperatu
r
w
ill only be e
n
t
point Offset f
e
bus and is st
o
M
odbus but i
s
M) losing po
w
o
r connected
t
p
erature of th
e
n
sate by adju
s
following equ
(BMS Room
Setpoint bein
g
Room Temp
e
e
Temperatur
e
r
e setpoint fro
n
abled for, Air
-
e
ature, BMS
R
o
red in non-vo
s
not stored in
w
er.
t
o a BMS or
o
e
indoor unit.
T
s
ting the indo
o
ation:
Temperatur
e
g
set to 21ºC
a
e
rature decre
a
e
Setpoint = 2
2
m rapidly cha
-
To-Air type u
R
oom Tempe
r
latile memory
non-volatile
m
o
ther controlle
r
T
he A1M can
c
o
r unit’s temp
e
e
– BMS Virt
u
a
nd the indoo
r
a
ses the Melc
o
2
– (18 – 21)
=
n
ging.
nits.
r
ature and B
M
y
so the value
m
emory, so th
r
may provide
calculate the
d
e
rature setpoi
n
u
al Temperat
u
r unit return a
oBEMS MINI
=
25ºC.
14
M
S Virtual
is retained
e value is
a more
d
ifference
n
t.
u
re)
ir
(A1M)