ICE THICKNESS ADJUSTMENT
TO INCREASE OR DECREASE THE ICE THICKNESS
PRESS THE UP OR DOWN ARROWS WHEN THE ICE
MAKER IS IN ICE PRODUCTION OR ICE FULL MODE.
THERE ARE 5 ICE THICKNESS LEVELS, LEVEL 3 IS
THE DEFAULT FACTORY SET THICKNESS, LEVEL 5 IS
THE MAXIMUM, LEVEL 1 IS THE MINIMUM. WHEN
THE NEW THICKNESS HAS SELECTED THE DISPLAY
WILL FLASH 5 TIMES AND THE NEW VALUE STORED.
ICE FULL
WHEN THE STORAGE BIN IS FULL THE ICE FULL
INDICATOR ILLUMINATES RED AND THE ICE MAKER
WILL STOP ICE PRODUCTION AUTOMATICALLY.
THE DIGITAL DISPLAY WILL REVERT TO DISPLAYING
THE ROOM AMBIENT TEMPERATURE.
CLEAN
TO START A CLEAN CYCLE HOLD THE CLEAN
BUTTON FOR 3 SECONDS AND RELEASE WHEN THE
CLEAN ICON IS ILLUMINATED AND 05 IS SHOWN
IN THE DIGITAL DISPLAY. THE 5 MINUTE CLEAN
CYCLE WILL START, WHEN THE CLEAN CYCLE HAS
FINISHED THE ICE MAKER WILL AUTOMATICALLY
ENTER STANDBY MODE AND THE AMBIENT ROOM
TEMPERATURE WILL BE DISPLAYED IN THE DIGITAL
DISPLAY.
NOTE: THE CLEAN CYCLE WILL ONLY RUN WHEN
THE MACHINE IS IN STANDBY MODE.
TIMER
THE ICE MAKER IS FITTED WITH A TIMER FUNCTION
WHICH ALLOWS YOU TO SET HOW LONG THE ICE
MAKER WILL RUN BEFORE ENTERING STANDBY
MODE.
TO SET THE TIMER PRESS THE TIMING BUTTON
FOR 3 SECONDS AND RELEASE WHEN THE TIMING
LED IS ILLUMINATED AND THE DIGITAL DISPLAY IS
FLASHING. USING THE UP AND DOWN ARROWS
SELECT THE NUMBER OF HOURS YOU WOULD LIKE
THE MACHINE TO RUN FOR UP TO A MAXIMUM OF
12 HOURS. ONCE THE TIMER IS SET THE DISPLAY
WILL FLASH 5 TIMES AND ENTER ICE PRODUCTION
MODE. THE ICE MAKER WILL THEN CONTINUE
TO RUN UNTIL THE TIMER EXPIRES OR THE ICE
STORAGE BIN IS FULL OF ICE.
ERROR CODE POSSIBLE CAUSE
E1 WATER SHORTAGE OR INSUFFICIENT WATER PRESSURE
E2 HARVEST CYCLE TOO LONG
E3 CONDENSER SENSOR FAULTY
E4 EVAPORATOR SENSOR FAULTY
E5 AMBIENT SENSOR FAULTY
E6 CONDENSER TEMPERATURE TOO HIGH
E7 AMBIENT TEMPERATURE TOO HIGH OR TOO LOW
E8 ICE MAKING CYCLE TOO LONG
HOW THE ICE MAKER WORKS
ICE MAKING STAGE: WHEN THE POWER ON
BUTTON IS PRESSED THE MACHINE INITIALLY
PERFORMS A RINSE TO FLUSH THE EVAPORATOR
OF ANY CONTAMINANTS. WHEN THE RINSE CYCLE
HAS FINISH THE COMPRESSOR, WATER PUMP
AND CONDENSER FAN MOTOR WILL ENERGISE
STARTING THE FREEZING CYCLE.
WATER IS THEN CIRCULATED OVER THE
EVAPORATOR SURFACE FREEZING INTO ICE CUBES.
WHEN THE PRESET THICKNESS IS REACHED AND
THE ICE IS FULLY FORMED THE FREEZING CYCLE
ENDS AND THE HARVEST CYCLE BEGINS.
FOR FURTHER ASSISTANCE WITH THE ABOVE
ERROR CODES PLEASE CONTACT YOUR
AUTHORISED SERVICE PARTNER.
WARNING
ALTHOUGH THE ICE MAKER HAS BEEN
TESTED AND CLEANED AT THE FACTORY
DIRT AND PARTICLES MAY OF ENTERED THE
SYSTEM DURING TRANSIT, UNPACKING AND
INSTALLATION. DUE TO THIS IT IS IMPORTANT
THAT ALL ICE PRODUCED DURING THE FIRST 3
HOURS IS DISCARDED.
PART III
CL200718UM Rev 1.3
6
TABLE 1
TO CANCEL THE TIMER HOLD THE TIMING BUTTON
AGAIN FOR 3 SECONDS, THE MACHINE WILL
THEN ENTER STANDBY MODE. ALTERNATIVELY
PRESSING THE POWER BUTTON WILL ALSO
CANCEL THE TIMER AND THE MACHINE WILL
ENTER ICE PRODUCTION MODE IMMEDIATELY.
NOTE: THE TIMING MODE CAN ONLY BE SELECTED
WHEN THE MACHINE IS IN STANDBY MODE.
To Next Page
Loading...
